Technical Data; Maintenance And Cleaning - EINHELL NEW GENERATION NKH 1500 Manual De Instrucciones

Anleitung NKH 1500_SPK7:_
GB

4. Technical data:

Rated voltage:
Output: 1500 W (750 W / 1500 W)
Thermostat control:
Protection class:
Appliance dimensions, approx.:
5. Proper use
The appliance is designed only for private use, not
for commercial heating purposes.
6. Starting up
Important! Before using the appliance for the first
time, check that the voltage supply is the same as
the voltage details set out on the data plate. Read
safety instructions listed under section 1.
When the heater is used for the first time or after a
long period of rest it may emit an odor for a short
time. This is not a fault.
6.1 Topple cut-out
If the appliance topples during operation, it is
automatically turned off by the switch (Fig. 3/Item 8).
When the heater is placed upright again (the switch
(Fig. 3/Item 8) must be activated), the appliance
restarts immediately.
6.2 Heat output switch (Fig. 1/Pos. 1):
Off setting (0)
Fan setting (*)
Low heating output (1)
Maximum heating output (2)
6.3 Thermostat control/Room thermostat
(Fig. 1 / Item 3):
Switch on the required heating output. Turn the
control to "MAX" until the required room temperature
has been reached. Then turn down the control until
you hear a clear click. The thermostat control will
switch the radiator on and off automatically to
maintain the room temperature at an almost constant
level. However, this presupposes that the radiator
has sufficient output to cover the heating
requirements for the room.
6.4 Oscillation function (Fig. 2 / Item 7)
Set the cool blow mode or heat mode as describe
above, turn the switch (Fig. 2 / Item 7) to "I". The
device swivels 30° to the left and 30° to the right
(oscillation). To switch off the oscillation function and
6
24.04.2007 9:24 Uhr Seite 6
have the device blow in one specific direction set the
switch to "0".
230 V ~ 50 Hz
6.5 Overheat cut-out
In case of excessive heating, the heating function
Infinitely adjustable
shuts down automatically. The fan and the indicator
II
light (Fig. 1/Item2) remain on.
18 x 27 x 15 cm
If this case occurs, turn off the appliance, disconnect
the mains plug and wait a few minutes until it has
cooled. After eliminating the cause (e.g. a covered
air grille), the appliance can be switched on again. If
the overheat cut-out triggers repeatedly, please
contact your customer service center.

7. Maintenance and cleaning

Before carrying out any cleaning and maintenance
work the appliance must be turned off,
disconnected from the power supply and cooled
down.
Maintenance and repair work may only be carried
out by an electrical servicing contractor or your
customer service center.
Check the mains lead at regular intervals for signs
of defects or damage. A damaged mains lead may
only be replaced by an electrician or the customer
service responsible for your country in compliance
with the relevant regulations.
Use a damp cloth to clean the casing.
To clean to air intake filter press the release (Fig. 2
/ Item 5) downwards and clean the air intake filter
(Fig. 2 / Item 6) with a vacuum cleaner. Then
reinstall the air intake filter.
8. Storage
The radiator has to be stored in a dry place, covered
if possible.
9. Ordering spare parts
Please provide the following information on all orders
for spare parts:
Model/type of machine
Article number of the machine
ID number of the machine
Number of the required spare part
For our latest prices and information please go to
www.isc-gmbh.info
10. Waste disposal
The appliance, accessories and packaging should be
disposed of in an environmentally-friendly fashion,
i.e. by taking them to a recycling depot. Plastic parts
are coded for purposes of separation when recycling.