Publicidad
Idiomas disponibles
Idiomas disponibles
ENG
Instruction Manual ADJUST GU10/ QUATRO GU10
1.
Use as directed:
This product serves exclusively lighting purposes and may:
only be used with a voltage of 230V ~50Hz.
not be exposed to strong mechanical loads or to strong
contamination.
only be installed and operated after a condition inspection if the
product is dirty or has been moistened through storage.
not be modified or converted.
If these points named above are not adhered to, a short circuit or
electrical shock may occur!
2.
Technical Data:
Operating voltage:
230V ~50Hz
Safety class:
I
Safety type:
IP 67
Bulb:
QPAR, GZ/GU10, max. 35W
Dimensions:
ADJUST ROUND
ADJUST SQUARE
(Ø/H): 13,5 / 11,5
(L/W/H):
13,5/13,5/11,5 cm
Recess dim. (L/W/D):
12,5/12,5/12 cm
Ø-Cable:
3,5-10 mm
Weight:
1,2 kg
Importeur:
SLV Elektronik GmbH
IP 67: Protection against dust(dust-tight) - Protection against the
penetration of water when temporarily submerged.
3.
Installation
Attention: Switch off the power of the mains supply line or
respectively of the connection lead before doing any works
parts, which are supplied with the product or are described as accessories!
Otherwise the product or the installation might not be sufficiently safe.
Installation place:
The product is suited for recessed floor installation.
Make sure that the product is mounted on a stable, even and tilt-fixed
background.
The light exit should be placed at least so far from the illuminated surface,
as indicated as minimum distance on the type plate of the luminaire:
m
. Pay special caution to easily inflammable objects.
Use as power lead only a suitable earth cable. Do not use PVC cables.
Separate Installation Steps
Loosen the screws on the stainless steel shield and take off the shield
and the protective glass with the gasket (1).
Take the fitting out of the plastic pot (2).
Direct the earth cable through the opening of the plastic casing. Fix the
plastic casing firmly into the earth.
Remove the bulb holder (3).
Direct the earth cable, in sufficient length, through the cable screwing
(4).
Electrical Connection (5)
The electric connection may be executed only by an electric expert
who is familiar with the valid directives!
The product must be able to be separated by an all pole separation from
the current supply.
For electric connection attach the black or brown wire (live conductor) of
the main power supply with the clamp L and the blue wire (neutral
conductor) of the main power supply with the clamp N. The green-
yellow wire (protective conductor) of the main power supply has to be
tightly screwed into the earth clamp
Fix the bulb holder again.
Secure the cable screwing.
Put the lamp into the plastic pot. Secure the screws.
Inserting the bulb (6): Insert the bulb with a slight turn into the socket.
Put the protection glass with gasket on the fitting. The part of the gasket
that is jutted out must point downwards.
Fasten the stainless steel shield back on the fitting. Fasten the screws
crosswise.
The product is now ready for operation.
ADJUST QUATRO
(L/W/H): 13/13/12 cm
.
Use only
0,5
4.
Operation
Information for the user:
Operate the product only if it is working correctly. Switch off the product
with a malfunction immediately and operate it again only after examination
by an electrical specialist. This is the case, when:
visible damages appear.
the product does not work.
smoke, steam or crackling sounds appear.
an overheating is recognisable.
Repairs of the product or work on mains voltage-prominent sections may
only be carried out by qualified electricians.
of the product.
1
6
3
5
2
4
3,5-10mm
125 mm
:
Attention: Here exists mortal danger from an electric shock!
How to avoid failure and fire risk:
Do not cover the product (Remove leaves and dirt once in a
while).
Do not fasten anything on the product.
Replace damaged protection glasses immediately!
Never let children play unsupervised with electric products! Children
can not always estimate dangers in dealing with electric energy correctly.
What is to do if a bulb is defect or does not work?
Disconnect the product from power, before you exchange
the bulbs.
Caution: Let the bulb cool down first before replacement –
otherwise considerable risk of injury exists because of the hot
surface.
Replace the bulbs only with bulbs of the same data like socket,
power and capacity. Every other sort of bulb can lead to
damages of the light.
Replacing the bulb: see Installation.
5.
What else has to be considered?
Disconnect the product from power, before you...
clean or maintain the product.
do any works on the product or its components (electric expert).
F
Mode d'emploi ADJUST GU10/ QUATRO GU10
1.
A utiliser comme indiqué :
Ce produit ne sert qu'à éclairer:
il est prévu pour une tension de 230V ~50Hz.
il ne doit être soumis ni aux efforts mécaniques importants ni à un
encrassement important.
il ne doit être utilisé qu'après examen si le produit a été stocké dans un
entrepôt humide ou sale.
ne doit pas être modifié.
Un non-respect de ces points peut causer un court-circuit ou une
décharge électrique!
2.
Informations techniques:
Tension d'alimentation:
230V ~50Hz
Classe de protection:
I
Degré de protection:
IP 67
Ampoule:
QPAR, GZ/GU10, max. 35W
Dimensions:
ADJUST ROUND
ADJUST SQUARE
(Ø/H): 13,5 / 11,5
(L/L/H):
13,5/13,5/11,5 cm
Mesures d'installation(L/L/P): 12,5/12,5/12 cm
Ø-câble:
3,5-10 mm
Poids:
1,2 kg
Importeur:
SLV Elektronik GmbH
IP 67: Protection contre la pénétration de poussière - Protection
contre la pénétration de l'eau en cas d´immersion temporaire.
3.
Installation
Attention: Mettez l'alimentation électrique ou le raccordement au
secteur hors tension avant de travailler!
Utilisez seulement des pièces qui ont été livrées avec le produit ou qui sont
uniquement décrites comme accessoires ! Sinon, l'installation ainsi que le
produit ne peuvent pas être garantis.
Lieu d'installation
ADJUST QUATRO
(L/L/H): 13/13/12 cm
Publicidad
