Troubleshooting; Maintenance; Demolition; Warranty - Tecomec Baby Jolly Manual De Instrucciones

GB
- once all right teeth have been ground, stop the grinder
- turn the wheel motor casing from the opposite side of the same grade, loosening the black knob (photo 5 – point 1)
- stand near the side facing the bar, to avoid the flow of sparks caused by the wheel
- position the rear part of a left tooth against the chain stop (photo 7)
- start the grinder and, slowly tilting the wheel towards the operator, work on the tooth; at this point, set the same grinding depth set for
right teeth, activating the relevant register positioned on the side of the grinder, and from the same tilting part of the wheel (photo 8
– point 1)
- after determining the quantity to be removed, the register remains in position, held by a spring
- at the end of the registration, complete grinding of all left teeth
- to avoid overloading the motor and to prevent the chain from being damaged, remove minimum quantities of material and
do not work too long on the same tooth, so as not to damage the cutter
At the end of grinding operations, turn off the grinder, disconnect the cable from the mains, and remove the grinder from the bar, placing
it in a safe place.
N.B. If the chain depth gauge is too high with respect to the tooth (usually after 2/3 grinding operations), lower it using a flat file (photo
9). For the height of the depth gauge, consult the chain table enclosed at the end of the handbook (column M).
N.B.
- Do not use cooling fluids while grinding
- if, when you turn the switch to "1", the grinder does not start, and if when the switch is in the "0" position the grinder does
not stop, promptly disconnect the power cable from the mains
- if the grinder does not switch on when the switch is turned to "1", immediately disconnect the power supply cable
- if the wheel is banged or hit by accident during grinding, follow the instructions provided in paragraph ASSEMBLY AND
WARNINGS ABOUT THE GRINDING WHEEL

TROUBLESHOOTING

The machine does not start:
- check that the plug is perfectly connected to the outlet
- check that the power cable of the machine is not damaged
- check that the outlet is energized
- check that no fuses have blown in the outlet
- check that the automatic circuit-breaker has not tripped.
If, after these operations, the failure to start can be attributed to the machine, have it checked by an authorized service center.
The connection of the machine to the mains makes the automatic circuit-breaker trip:
- contact an authorized service center.
The machine's electrical motor is overheated:
- check that the voltage indicated on the data plate meets the mains voltage
- comply the max. time (15 min.) recommended for continuous operation
- check that la wheel does not block during grinding
If the problem persists, contact and authorized service center.
The direction of rotation of the wheel is the opposite of that indicated on the machine:
- contact an authorized service center
The machine shows signs of anomalous vibrations:
- check that the machine is secured to the bar of the motor-driven or electrical saw
- check that the motor unit is secured to the base unit
- check that the wheel is properly installed on the relevant centering hub
If the problem persists, contact and authorized service center.

MAINTENANCE

- always disconnect the plug from the socket before carrying out any maintenance, lubrication or cleaning operations
- the grinder must be kept clean, in order to make safety instructions and plates clearly legible. Clean it using a rag or a swab.
- do not use compressed air, that is likely to bring the metal dust in positions where they cannot be reached, damaging essential com-
ponents of the grinder.

DEMOLITION

The baby jolly grinder has been fabricated with 90% recyclable materials. Therefore, if the grinder must be deactivated, do not abandon
it. Take it to your dealer who will store or dispose of it correctly.

WARRANTY

- the validity of the warranty on this product is subject to the recognition of the country of sale. To be valid, any claim must
be accompanied by a copy of the purchase documents (invoice or cash voucher). For any repairs, the machine must be sent,
carriage free, to your dealer.
- The warranty will be void if:
a. the grinder has been tampered with;
b. the grinder has not been used according to this manual;
c. non-original and/or unauthorized parts, tools, or grinding wheels have been fitted on the machine;
d. the grinder has been connected to voltage values other than the one stated on the serial number plate.
12