Publicidad
Idiomas disponibles
Idiomas disponibles
6 - Technical details
The display unit is accompanied by a plastic envelope containing this instruction manual. This manual must be kept with the machine. It
contains all the technical data, wiring diagrams and tables needed for the unit.
The following technical data are also shown on the serial plate (FIG. 8 on page 3):
1.
Commercial name of the refrigerating display unit;
2.
Refrigerating display unit code;
3.
Refrigerating display unit serial number;
4.
Rating;
5.
Frequency;
6.
Max absorbed power;
7.
Max absorbed power during defrosting;
8.
Standard lighting power;
9.
Net display area;
10.
Net capacity;
11.
Type of cooling gas used;
12.
Weight of cooling gas loaded in each unit;
13.
Climatic class and reference temperature (dry bulb);
14.
Functioning class depending on product storage temperature;
15.
Electrical safety factor;
16.
Work schedule number;
17.
Work order number;
18.
Year of manufacture.
Warning: The serial plate and the warning labels must never be removed from the unit. The Manufacturer cannot be held liable for any
damage or injury if this warning is ignored.
The Manufacturer states that this unit complies with Italian legislative degree n° 108 dated 25.01.1992, implementing EEC Directive
89/109 concerning materials and objects that come into contact with food.
7 - Loading and use of the unit (start-up)
If the display unit has been tipped during positioning and installation, wait at least three hours before starting it up in order to give the
lubricating oil enough time to collect in the compressor! The refrigerating unit may be irretrievably damaged if this precaution is ignored.
The display unit can only be started up for the very first time after complying with points 3 and 4 above.
With the unit unplugged, remove the plastic film protecting the insides and outside and then clean (follow the instructions in point 10
below).
Screw on the back spacers as shown in FIG. 13 on page 4. Fit the various shelf supports at the height required, as shown in FIG. 14 on
page 4. FIG. 1 on page 1 shows the best distances between shelves.
Plug in the unit (having followed the instructions in point 5) and then use the switch on the front panel to start the motor and the light
switch on the top panel (see FIG. 12 on page 3). A slight humming of the motor indicates that the unit is powered up.
Products can be loaded three hours after the unit has been switched on. The thermometer inside the display unit (see FIG. 12 on page 3)
will indicate the working temperature. The unit is designed to display food products and so maintains the temperature of the product; it
does not lower it. The product should, therefore, only be loaded once its right storage temperature has been reached.
Recommendations for storage:
-
Never block the cooling outlets that guarantee the correct flow of air (see FIG. 15 on page 4).
-
When loading a display unit that's already partially loaded, it's best to place the new products below those already inside (as well as
observing the above points).
-
At night, use the night cover (available on request), as this makes for energy savings and helps preserving the products on display.
The OSCARtielle GENIUS units normally have mechanical temperature control. The thermostat control and gas filling devices are set in
the factory. The Manufacturer cannot be held liable for any damage or injury should these be tampered with
7 - Loading and use of the unit (start-up)
If the display unit has been tipped during positioning and installation, wait at least three hours before starting it up in order to give the
lubricating oil enough time to collect in the compressor! The refrigerating unit may be irretrievably damaged if this precaution is ignored.
The display unit can only be started up for the very first time after complying with points 3 and 4 above.
With the unit unplugged, remove the plastic film protecting the insides and outside and then clean (follow the instructions in point 10
below).
Fit the various shelf supports at the height required, as shown in FIG. 11 on page 4 (GUAM BT-BT) and FIG. 12 on page 4 (GUAM BT-
TN). FIG. 1 on page 1 shows the best distances between shelves.
Plug in the unit (having followed the instructions in point 5) and flip the switch fitted upstream (if any). A slight humming of the motor
and the lighting-up of the display indicate that the unit is powered up.
Switch on the deep-freezer and display lights using the switch on the decorative front panel (see FIG. 10 on page 3).
The GUAM refrigerated combination has two displays (see FIG. 10 on page 3): one for the lower section (on the motor cover) and the
other for the top section (on the front panel). The electronic control instruction handbook for the displays is attached to the instruction
manual. A password guarantees that these devices cannot be tampered with.
The product can be loaded three hours after the unit has started its cooling cycle (check the temperature shown on the display).
The unit is designed to display food products and so maintains the temperature of the product; it does not lower it. The product should,
therefore, only be loaded once the right storage temperature has been reached.
Never place glass bottles/containers or jars full of liquid in the BT versions as there is the risk that these may explode/shatter.
12
Publicidad
