Reverse Function - Rexel Auto+ 60X Manual De Instrucciones

Autofeed Technology
The Auto+ 60X has been designed to automatically shred up
to 60 sheets from the autofeed chamber and up to 5 sheets
through the manual feed slot. The auto-feed mechanism has
been designed to handle paper fastened with staples and paper
clips and to only pull a few sheets of paper into the cutting
mechanism to minimise the risk of paper jams.
Operation
Unpack the product.
1
Connect the shredder to mains supply.
2
Ensure the on/off switch on the back of the shredder is in
3
the 'ON' position, which will illuminate the blue LED bulb
below the standby symbol (
To commence shredding, move the slide switch to the Auto
4
position ( ) which sets the shredder into auto mode. You
are now ready to shred.
To load the shredder, simply lift the loading door catch
5
(see fig. 1) to open the loading door and insert documents.
You can open the door further to 90 degrees for easier
access if required. Load up to 60 sheets at a time into the
feed chamber. Do NOT fill above the MAX level, this could
damage the shredder (see fig. 2).
The shredder will start shredding automatically ONLY after
6
closing the loading door (see fig. 1).
If there is still paper in the Autofeed tray after first attempt,
7
open and re-close paper loading door a second time.
If you only have up to 5 sheets to shred, you can use the
8
manual feed slot, provided the auto feed chamber is empty
(see fig. 3).
Bin or Loading Door Open Safety
Function
As a safety precaution, if the bin or loading door is opened
during shredding, the shredder will stop.
Rare Occasions of Jamming
In the unlikely event of the shredder jamming, the Auto+ 60X
will stop shredding. Check that the bin is not full then try
clearing the jam using the reverse (
boost ( ) switch then return to Auto mode (
unsuccessful follow the reverse function instructions.
6
).
) and continuous jam
). If this is

Reverse Function

Should you wish to reverse paper out whilst shredding, a
1
reverse button ( ) has been fitted for your convenience.
Reverse the paper out then turn the shredder off using the
2
ON/OFF switch at the rear of the shredder. Remove the
paper from the manual feed slot (if being used) or open the
loading door, remove the remaining stack of paper, then pull
the jammed paper free of the cutting mechanism.
To resume shredding return the slide switch to the auto
3
position ( ) and turn on the machine by using the ON/OFF
switch at the rear of the shredder.
Over Heating
If the Auto+ 60X is used continuously for over 8 minutes the
shredder may overheat and the red cool down indicator will
illuminate underneath the thermometer symbol (
allow the shredder to cool down. When the shredder is ready
to be used the thermometer symbol will no longer illuminate. If
the shredder needs to cool down while shredding, no action is
needed. The shredder will automatically restart shredding paper
once it has cooled down after periods of continuous use. All you
need to do is ensure paper is loaded into the chamber and the
bin is empty when the machine is cooling down.
Credit Card Shredding
The Auto+ 60X can shred credit cards. Switch the shredder to
auto mode and insert the credit card between the markings in
the manual feed slot (see fig. 4). Only shred one credit card at
a time.
Rexel encourages customers to recycle shredded paper.
Please note that shredded paper cannot be recycled
if mixed with credit card shards. If recycling, please
separate shredded paper and credit cards.
Bin Full
Should the shredder stop shredding, the bin may be full. Check
first by looking through the viewing window and if full you
should empty the bin.
• Pull open the bin slowly to empty.
• Push the empty bin back into place and the machine will
resume shredding.
). Please