Before Starting The Equipment - Toolson PRO-AS 14,4 Manual De Instrucciones

Anleitung PRO_AS_14_4_SPK7:_
GB

5. Before starting the equipment

Be sure to read the following information before you
use your cordless screwdriver for the first time:
1. Charge the battery pack with the charger
supplied. An empty battery pack requires a
charging period of approximately 1 hour.
2. Only ever use sharp drill bits and screwdriver bits
which are suitable for the purpose and in
faultless condition.
3. Always check for concealed electric cables and
gas and water pipes when drilling and screwing
in walls.
6. Operation
6.1 Charging the NC battery pack (Fig. 2/3)
1. Remove the battery pack (5) from the handle,
pressing the pushlock buttons (8) downwards to
do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Plug the mains plug of the charger (6)
into the mains socket outlet.
3. The green LED on the charger will come on.
Push the battery pack (5) onto the battery
charger (6). Now the rot LED will come on to
indicate that the battery pack is being charged.
When the charging period is completed after
approx. 1 hour, the green LED on the charger
will come on again. The temperature of the
battery (5) may rise during the charging
operation. This is normal.
If the battery pack fails to become charged, please
check
whether there is voltage at the socket-outlet
whether there is proper contact at the charging
contacts on the charger.
If the battery still fails to become charged, please
return
the charger
the battery pack
to our Customer Service Department.
Timely recharging of the Ni-Cd battery pack is
recommended in the interest of long battery life.
Recharging is always necessary when you notice
that the power of the battery-powered
drill/screwdriver is decreasing.
Never allow the battery pack to discharge
completely. This will result in damage to the Ni-Cd
12
11.03.2009 7:14 Uhr Seite 12
battery pack!
6.2 Adjusting the torque (Fig. 4/Item 1)
The battery-powered drill/screwdriver is equipped
with a 23-step mechanical torque adjustment facility.
The torque for a specific size of screw is selected
with the set-collar (Figure 1). The correct torque
depends on several factors:
on the type and hardness of material in question
on the type and length screws used
on the requirements needing to be met by the
screwed joint.
The clutch disengages with a grating sound to
indicate when the set torque is reached.
Important! The tool must be at a standstill when
you set the torque with the setting ring.
6.3 Drilling (Fig. 4/Item 1)
For drilling purposes, move the set-collar to the last
step „Drill". In this setting the slip clutch is inactive.
The maximum torque is available in drilling mode.
6.4 Forward/Reverse switch (Fig. 5/Item 3)
With the slide switch above the On/Off switch you
can select the direction of rotation of the battery-
powered drill/screwdriver and secure it against being
switched on accidentally. You can choose between
clockwise and anticlockwise rotation. In order to
avoid causing damage to the gearing, the direction of
rotation must only be changed when the screwdriver
is at a standstill. When the slide switch is in the
middle position, the ON/OFF switch is blocked.
6.5 On/Off switch (Fig. 5/Item 4)
Infinitely variable speed control is possible with the
On/Off switch. The further you press the switch, the
higher the speed of the battery-powered
drill/screwdriver.
6.6 Switching from speed 1 – speed 2
(Fig. 6/Item 7)
You can work with a higher or lower speed
depending on the position of the selector switch.
Change the gear only when the drill is at a standstill.
If you fail to observe this point, the gearing may be
damaged.
6.7 Battery capacity indicator (Fig. 7/Item 2)
Press the battery capacity indicator button (a) next to
the LCD display with the rechargeable battery
inserted. You can read off the present capacity of the
rechargeable battery in % from the LCD display.
When the battery is fully charged, the percentage will
be higher, when it is discharged, it will be lower.