Technical Data; Before Starting The Equipment - Robust RB-MG 12 Li Manual De Instrucciones

4. Technical data

Motor power supply: ............................... 12 V DC
Idling speed: .................................... 20000 min-1
Sanding/grinding area: .............. 90 x 90 x 90 mm
Protection class: ...........................................II /
Charge voltage for rechargeable battery: ............
................................................................ 12 V DC
Charge current for rechargeable battery: .... 0.4 A
Battery charger supply voltage: ...... 230 V ~ 50Hz
Charging time: ..............................max. 3-5 hours
Battery type: .......................................Lithium-ion
Weight: .....................................................0.65 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L sound pressure level ........................ 76 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level .......................... 87 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Handle
Vibration emission value a
K uncertainty = 1.5 m/s
Additional information for electric power
tools
Warning!
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to com-
pare the equipment with another electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Anl_RB_MG_12_Li_SPK7.indb 21 Anl_RB_MG_12_Li_SPK7.indb 21
= 3.26 m/s
2
h
2
- 21 -
GB
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

•
Before you connect the equipment to the
power supply make sure that the data on the
rating plate are identical to the supply voltage.
5.1 Fitting the plug-in tools (Figures 1/2/3)
•
To fit the plug-in tools safely you should hold
the multifunction tool so that the ON/OFF
switch (1) points down and the tool mounting
(2) faces up.
•
Place the plug-in tool (e.g. the triangular san-
ding/grinding plant) on the tool mounting (2)
so that the pins of the tool mounting (2) fit into
the recesses in the plug-in tool.
•
Secure the plug-in tool using the supplied
screw (b) and tighten the screw securely with
the Allen key (5).
•
Make sure that the washer (a) is used for
the screw (b) (see Figure 3). In this case the
corrugated face of the washer must be placed
against the plug-in tool.
Check that the plug-in tool is secure.
13.10.2016 09:46:07 13.10.2016 09:46:07