Jacobsen HR 4600 Turbo Manual De Piezas Y Mantenimiento página 154

HR-4600
1.1 Decals
OPERATION
READ MANUAL BEFOR OPERATING.
REPLACEMENT MANUAL AVAILABLE FROM:
JACOBSEN/TEXTRON, RACINE WI.
To Start
1. Parking Brake.............On
1. Traction Pedal......Neutral
2. Traction Pedal......Neutral
2. Mower Switch..............Off
3. Mower Switch.............Off
3. Parking Brake.............On
4. Throttle......................Half
4. Throttle.....................Slow
5. Ignition........................On
5. Ignition........................Off
5. Glow Plug Light.........Off
6. Remove Key
7. Ignition.....................Start
To Drive/Transport
1. Follow "To Start" 1. Follow "To Start"
Instructions.
2. Mower Switch.............Off 2. Throttle......................Fast
3. Cutting Units..........Raise 3. Mower Switch...........Mow
4. Parking Brake.............Off 4. Parking Brake.............Off
5. Throttle......................Fast 5. Cutting Units.........Lower
6. Slowly depress 6. Slowly depress
traction pedal
LF-3400: Engine Power: 25.0 kW @ 3000 rpm.
Vehicle Mass: 1160 kg (2WD), 1230 kg (4WD)
LF-3800: Engine Power: 28.0 kW @ 3000 rpm.
Vehicle Mass: 1250 kg (2WD), 1320 kg (4WD)
HR-4600: Engine Power: 35.0 kW @ 3000 rpm.
Vehicle Mass: 1250 kg
3
2
10
3
7
5
8
6
28
STARTING THE TRACTOR
THE FOLLOWING LAMPS MUST BE ON WHEN THE
To Stop/Park
IGNITION KEY IS IN THE "RUN" POSITION:
LAMP
3..PROGRAM ACTIVE (INDICATES CONTROLLER
HAS POWER)
5.....NEUTRAL START SWITCH (TRANSPORT PEDAL)
6.....BRAKE SWITCH (PEDAL MUST BE ENGAGED)
31....GLOW PLUG RELAY AND INDICATOR-
(DURATION THE LAMP IS LIT DEPENDS ON
ENGINE TEMPERATURE)
To Mow
THE FOLLOWING LAMPS MUST BE OFF WHEN THE
IGNITION KEY IS IN THE "RUN" POSITION:
Instructions.
4.....KEY SWITCH-"START" POST
25...REEL SWITCH-FORWARD DIRECTION-PIN 1
33...START RELAY AND INDICATOR
37...REEL SWITCH-LEFT WING ACTIVE SIGNAL
38...REEL SWITCH-CENTER ACTIVE SIGNAL-PIN 5
traction pedal 39...REEL SWITCH-RIGHT WING ACTIVE SIGNAL
ALL OTHER LAMPS DO NOT AFFECT
THE STARTING OF THIS MACHINE.
"RUN"
POSITION
"OFF"
POSITION
LAMP ON = CIRCUIT IS ACTIVE
LAMP OFF = CIRCUIT IS INACTIVE
1
20
CONTROLLER FUNCTIONS BY LAMP NUMBER
LAMP SIGNAL CIRCUIT
3....INPUT...PROGRAM ACTIVE (INDICATES CONTROLLER
HAS POWER)
4....INPUT...KEY SWITCH-"START" POST
5....INPUT...NEUTRAL START SWITCH
6....INPUT...BRAKE SWITCH
7....INPUT...SEAT SWITCH
9....INPUT...CRUISE CONTROL SWITCH-OFF-PIN 1
10...INPUT...CRUISE CONTROL SWITCH-ON-PIN 6
11...INPUT...HYDRAULIC OIL LEVEL FLOAT SWITCH
12...INPUT...HYDRAULIC OIL LEVEL ALARM SWITCH-PIN 3
13...INPUT...ENGINE OIL PRESSURE SWITCH
16...INPUT...LIFT LIMIT SWITCH-LEFT WING
19...INPUT...LIFT LIMIT SWITCH-RIGHT WING
20...INPUT...JOYSTICK-LEFT-PIN 4
21...INPUT...JOYSTICK-RIGHT-PIN 5
22...INPUT...JOYSTICK-LOWER-PIN 3
23...INPUT...JOYSTICK-RAISE-PIN 2
25...INPUT...DECK SWITCH-FORWARD DIRECTION-PIN 1
31...OUTPUT...GLOW PLUG RELAY AND INDICATOR
32...OUTPUT...LIGHT TEST
33...OUTPUT...START RELAY AND INDICATOR
34...OUTPUT...FUEL HOLD COIL
"START" 35...OUTPUT...WARNING HORN
POSITION
36...OUTPUT...HYDRAULIC OIL LEVEL LIGHT
37...OUTPUT...DECK SWITCH-LEFT WING ACTIVE SIGNAL-PIN
38...OUTPUT...DECK SWITCH-CENTER ACTIVE SIGNAL-PIN 5
IGNITION SWITCH POSITIONS 39...OUTPUT...DECK SWITCH-RIGHT WING ACTIVE SIGNAL-PIN 5
LOCATED ON THE 40...OUTPUT...CRUISE CONTROL COIL/LIGHT(OPTION)
41...OUTPUT...VALVE-LIFT PRESSURE
INSTRUMENT PANEL
42...OUTPUT...VALVE-RAISE-LEFT WING
43...OUTPUT...VALVE-RAISE-CENTER
44...OUTPUT...VALVE-RAISE-RIGHT WING
45...OUTPUT...VALVE-LOWER-LEFT WING
46...OUTPUT...VALVE-LOWER-CENTER
47...OUTPUT...VALVE-LOWER-RIGHT WING
LAMPS NOT USED: 1,2,8,14,15,17,18,24,26,27,28,29,30,48
SEE OPERATOR'S MANUAL FOR MORE DETAILED INSTRUCTIONS.
13
12
9
11
15
16
HR 4600 TURBO
17 / 18
13
2
4
4WD
14
19
Serial No. All
1