Product Parts - Peg-Perego Si switch Instrucciones De Uso

_ Do not load the baskets over 5Kg. Do not put weight
in the cup holder (if present) in excess of those
indicated on the cup holders themselves and never
hot drinks. Do not put loads of more than 0.2 Kg in
the hood pockets (if present).
_ Do not use the product near to stairs or steps, heat
sources, naked flames or dangerous objects within
reach of the child.
_ Only replacement parts supplied or recommended by
the manufacturer/distributor shall be used.
_ WARNING Don't use the rain cover (if present)
on a product without a hood or parasol that can
hold it. Always use the rain cover only under adult
supervision. Don't use the rain cover indoors and
check to ensure the child is not to warm; do not
park the vehicle close to heat sources and keep well
away from the lighted cigarettes. Ensure that the rain
cover is not interfering with any moving parts of the
carriage/stroller. Always remove the rain cover before
folding your carriage/stroller.
_ WARNING This product is not suitable for running or
skating.
_ Always apply the brake when loading or unloading
children.
_ WARNING Do not add any mattress.

PRODUCT PARTS

Check the package contents and contact our Customer
Service for any claim.
_ The Si Switch COMPLETO stroller includes: 2 swiveling
or locking front wheels, 2 rear wheels, a basket, a hood,
a foot muff, a front bar, and a rain canopy.
_ The Si Switch CLASSICO stroller includes: 2 swiveling
or locking front wheels, 2 rear wheels, a basket, a hood,
a front bar.
INSTRUCTIONS
1• OPENING THE STROLLER: lift the side levers on the
handles simultaneously (fig_a) and pull upwards until
the stroller opens. To ensure it has opened properly,
check that the side tubes are fastened together (fig_b).
2• If the hooks are not secured properly, press the seat
downwards (fig_c) until they click into place. Finally,
press downwards with your foot (fig_d).
3• Place the front bar into the position of use by lifting it
upwards until it locks into place (fig_e).
4• BASKET: to mount the basket, slip the loops over the
rear hooks A and B and the front hooks C and D.
5• BRAKE: To set the brake on the stroller, lower the lever
on the rear wheel unit with your foot. To release the
brake, lift the lever (fig_a). When stationary, always
apply the brake.
SWIVEL WHEELS: to make the front wheels swivel,
lower the lever (arrow 1). To lock them, push the lever
in the opposite direction (arrow 2). The rear wheels are
fixed (fig_b).
6• FRONT BAR: It can be put in 2 positions:
POSITION 1: Use.
POSITION 2: Folding.
To adjust it, press the two side buttons at the same time.
7• The front bar can only be opened on one side, to make
it easier for the child to get in and out of the stroller
when he or she is bigger. To open the front bar, press
the button under the armrest and at the same time
pull the front bar outwards (fig_a). To remove the front
bar, press the two buttons under the armrests and at
the same time pull the front bar outwards (fig_b).
To attach the front bar, insert the two ends into the
armrests until they lock into place (fig_c).
8• HOOD: Open the zipper to extend the hood and
protect your child from the sun even with the stroller's
backrest fully reclined (fig_a).
Lifting the cloth flap reveals a mesh insert that allows
you to see the child while asleep and promotes better
ventilation (fig_b).
To release the hood, unfasten the attachments on the
two sides of the seat (fig_c)
The hood includes a slot from which you can hang
your child's favorite toy (fig_d).
9• FOOT MUFF Si Switch COMPLETO: to fasten it
correctly, slip the foot muff under the footrest and leg
rest and place it over the seat, keeping the front bar on
the outside. Fasten the FIRST button of the foot muff
to the inside of the stroller (fig_a) and hook the frog
fastenings, also to the front bar (fig_b).
On lowering the stroller's backrest, it is possible to
place the foot muff higher up and cover the child
better. To do this, fasten the SECOND button of the
foot muff to the inside of the stroller (fig_c) and hook
the frog fastenings to the highest loops (fig_d).
10• RAIN CANOPY Si Switch COMPLETO: to add the rain
canopy, place it on the stroller, fasten it at the sides to
the inside of the frame (fig_1), and fasten the elastics
after pulling them round the lower part of the stroller
frame (fig_2).
11• 5-POINT SAFETY HARNESS: to fasten, insert the two
buckles of the waist strap (with attached shoulder
straps, arrow a) into the leg divider strap until they
click into place (arrow b). To unfasten them, press the
button which is situated in the centre of the fastener
(arrow c) and pull the waist strap outwards (arrow d).
12• To tighten the waist strap, pull on both sides in the
direction of the arrows; to loosen it, do the opposite.
13• It is possible to set the safety harness at 3 different
heights, depending on how tall the child is. As the
child gets bigger, the harness must be moved to a
higher position.
14• To adjust the height of the safety harnesses, release
the two buckles on the rear of the backrest.
Pull the shoulder straps towards you (arrow a) until the
buckles are released and insert them in the backrest
loops (arrow b). Remove the shoulder straps from the
sack (arrow c) and insert them in the most appropriate
buckle (arrow d), then reattach the two buckles
behind the backrest (arrow e). The buckles are securely
attached when a click is heard (fig f).
15• ADJUSTING THE LEG REST: The leg rest can be adjusted
in 2 positions. To lower it, pull the two side levers
downwards and at the same time lower the leg rest. To
raise it, push the leg rest upwards until it locks into place.
ADJUSTING THE BACKREST: The backrest reclines into
various positions. To lower the backrest, lift the handle
and simultaneously lower the backrest, locking it in
desired position. To raise it, push the backrest upwards.
16• REVERSIBLE SEAT The seat can be attached to the
frame facing either mom (fig_a) or the world (fig_b).
17• RELEASING/FASTENING THE SEAT
To release the seat: press the side buttons
simultaneously and lift the seat, which will have
unfastened, by pressing on the rounded area of the
structure, as shown in the figure (fig_a).
To fasten the seat: place it on the frame with the side
buttons corresponding to the relevant holes; the seat
will click into place (fig_b).
- 16 -