Charging Procedure; Checking The Charger - Stiga BT 48 Li 2.0 Manual De Instrucciones

(for cell UR18650RX) The cells LG made
used in battery pack BT 48 Li 2.5 and BT
48 Li 5.0 were approved by UL according
to the standard IEC 62133: 2012 (Second
Edition). The CB certificate No. DK-34524-
UL (for cell ICR18650HE2/ICR19/66)
• Charging only rechargeable Batteries.
• LED turns green blinking during charging,
and green during after charging.
• The disconnection from line voltage
is made by pulling the mains plug.
• The socket outlet must be located close to
the machine and be easily accessible.

CHARGING PROCEDURE

NOTE The battery is not shipped fully
charged. It is recommended to fully charge before
use to ensure that maximum run time can be
achieved. This lithium-ion battery will not develop
a memory and may be charged at any time
1. Plug the charger into an AC power outlet..
2.Insert the battery pack (1) into the charger (2).
CG 48 Li
This is a diagnostic charger. The Charger
LED Lights (3) will illuminate in specific order
to communicate the current battery status.
They are as follows:
CG 48 Li:
CHARGING PROCEDURE (LED INDICATOR )
BATTERY IS CHARGING:
FULL CHARGED:
BATTERY IS TOO WARM OR TOO COLD:
(REMOVE FOR APPROX.30 MINUTES TO ALLOW
TO COOL)
NO BATTERY PRESENT:
DEFECTIVE BATTERY:
(REMOVE AND REPLACE WITH NEW BATTERY
IF THIS OCCURS)
CGF 48 Li
GREEN
BLINKING
GREEN
RED
OFF
RED
BLINKING
CGF 48 Li:
CHARGING PROCEDURE (LED INDICATOR )
BATTERY IS CHARGING:
FULL CHARGED:
BATTERY IS TOO WARM OR TOO COLD:
(REMOVE FOR APPROX.30 MINUTES TO ALLOW
TO COOL)
NO BATTERY PRESENT:
DEFECTIVE BATTERY:
(REMOVE AND REPLACE WITH NEW BATTERY
IF THIS OCCURS)
False Defect Note:
When the battery is inserted into the charger,
and the status LED flashes, remove the
battery from the charger for 1 minute, then
reinsert. If the status LED indicates
normal than the battery pack is good. If
the status LED is still blinking, remove
the battery pack and unplug the
charger. Wait 1 minute and plug the charger
back inand reinsert the battery pack. If the
status LED indicates normal than the battery
pack is good. If the status LED is still blinking
then the battery pack is defective and needs
to be replaced.
NOTE When the red indictor flickers, pull out
the battery from the charger and insert again
within 2 hours. If the indictor shows charging,
that means the battery is good. After 2 hours,
please pull out the battery and also pull out the
AC power plug of the charger for 1 miniute, and
then insert the AC power plug and the
battery again. If the indictor shows charging,
that means the battery is good. If not,
the battery needs to be changed.

CHECKING THE CHARGER

If the battery pack does not charge properly::
• Check the current at the power
outlet with another tool. Make sure
that the outlet is not turned off.
• Check that the charger contacts have not
been shorted by debris or foreign material.
• If the surrounding air temperature is not
normal room temperature, move the charger
and battery pack to a location where the
temperature is between 7 ˚C and 40˚C .
If the battery is inserted into the charger
when warm or hot, the CHARGING LED
indicator light on the charger may switch
on and illuminate ORANGE. If this occurs
allow the battery to cool outside of the
charger from approximately 30 minutes.
EN - 4
GREEN
RED
BLINKING
GREEN RED
OFF
RED
BLINKING
RED
OFF
GREEN
RED
BLINKING
BLINKING