Cleaning And Maintenance; Disposal And Recycling; Troubleshooting Guide - Mecafer Super Silent 425543 Manual De Instrucciones

7. CLEANING AND MAINTENANCE

Warning!
Pull the power plug before doing any cleaning and maintenance
work on the appliance.
Warning!
Wait until the compressor has completely cooled down. Risk of
burns!
Warning!
Always depressurize the tank before carrying out any cleaning
and maintenance work.
7.1 Cleaning
● Keep the safety devices free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it with compressed
air at low pressure.
● We recommend that you clean the appliance immediately after
you use it.
● Do not use cleaning agents or solvents; these may be aggressive to
the plastic parts in the appliance. Ensure that no water can get into
the interior of the appliance.
● You must disconnect the hose and any spraying tools from the
compressor before cleaning. Do not clean the compressor with water,
solvents or the like.
7.2 Draining tank
The condensation water must be drained off each day by opening the
drain valve (ref. D) (on the bottom of the pressure vessel) (fig. 9).
1. Verify that the compressor is turned Off.
2. Holding the handle, tilt the compressor toward the drain valve so
that it's set in a lower position.
3. Open gently the drain valve.
4. Keep the compressor tilted until all moisture has been removed.
5. Close the drain valve.
Warning!
Dispose of the condensation water in an environmentally
compatible manner at the appropriate collection point.
7.3 Safety valve (ref. F)
The safety valve has been set for the highest permitted pressure of the
pressure vessel. It is prohibited to adjust the safety valve. Actuate the

9. TROUBLESHOOTING GUIDE

Note: Remove power source and drain tank pressure prior to making any repairs or adjustments.
Fault
The compressor stops and restarts
automatically after a few minutes.
After a few attempts to restart, the
compressor stops.
The compressor does not stop and the
safety valve is tripped.
Any other type of operation must be carried out by authorized Service Centers, requesting original parts. Tampering
with the machine may impair its safety and in any case make the warranty null and void.
Warranty and repair.
In the event of defective goods or requirements for spare parts, kindly contact the sales point where you made your purchase.
safety valve from time to time to ensure that it works when required.
Pull the ring with sufficient force (fig. 10) until you can hear the
compressed air being released. Then release the ring again.
7.4 Storage
Warning!
Disconnect the plug from the socket, vent the appliance and
tools connected to it and empty the condensate.
Switch off the compressor and make sure that it is secured in
such a way that it cannot be started up again by any unauthorized
person.
Warning!
Store the compressor only in a dry location which is not
accessible to unauthorized persons.
Always store upright, never tilted!

8. DISPOSAL AND RECYCLING

and electronic equipment (WEEE).
The symbol carrying a crossed-out refuse container depicted on any
equipment or the relative packaging means that, at the end of its useful
life, said product must be disposed of separately from other waste.
The user must therefore take said equipment to the centres
specialising in differentiated refuse collection of electric and electronic
equipment or alternatively return it to the reseller when purchasing a
new similar piece of equipment.
Thanks to differentiated refuse collection, discarded equipment can
be sent to be recycled, treated and disposed of in an environmentally-
friendly manner; this helps avoiding possible negative effects on the
environment and on health and promotes the re-employment and/or
recycling of the equipment's materials.
Any unauthorised disposal of the product by the user will result in the
application of the fines provided for by the regulations in force.
Cause
Tripping of the thermal cutout due to
overheating of the motor.
Tripping of the thermal cutout due to
overheating of the motor (removal of the
plug with the compressor running, low
power voltage).
Irregular compressor operation or pressure
switch malfunction.
19
Pursuant to Directive 2012/19/EU on waste electrical
Remedy
Allow the compressor to cool down.
Ventilate the work area.
Activate the on/off switch. Ventilate the work
area. Wait a few minutes. The compressor
will restart independently.
Remove the plug and contact the Service
Center.
G
B