SUHNER ABRASIVE USF 6R Instrucciones De Uso página 5

cooling effect in no load mode. Repeated
automatic cut off indicates, tool is being
overloaded.
4.Caution: Electrical surges and high
frequency interference may cause RPM
fluctuations up to 30% which will disappear as
soon as power source conditions stabilize.
Due to electromagnetic interference at a lower
speed range the drive motor may shut-off
prematurly. In this case, activate on/off switch
and restart.
Attention: Even if the cut-out is not activated,
danger of overloading always exists, thus
don't force the tool in order not to increase
unnecessarily excessive current draw, which
overheads the motor.
Speed selection for USF 6R/USF11R
Select required speed with variable speed
selector 10 for correct surface feet./M.O.S.
Speed selector
Position rpm
1 2'500
2 3'100
3 3'700
4 4'300
5 5'000
6 5'600
Attention: Do not change pre-selected speed
while tool is running and has working tools
mounted.
Polishing / Cleaning
• Observe even material removal, avoid
chattering.
• Do not treat any material containing asbes-
tos.
USA / CANADA
Suhner Industrial Products Corp.
Highway 411 South and Suhner Drive
P.O. Box 1234
Rome, GA 30162 - 1234
Phone 706 / 235 80 46
Fax 706 / 235 80 45
e-mail: info@suhnerusa.com
URL:www.suhnerusa.com
GERMANY:
Otto Suhner GmbH
P.O. Box 1041, D-79701 Bad Säckingen
Trottäcker 50, D-79713 Bad Säckingen
Tel. 0 77 61/557 0
Fax 0 77 61/557 190
e-mail: info@suhner.de
http://www.suhner.de
Disconnect Tools,
When changing accessories and abrasives,
burs, brushes etc.
• Hold spindle with wrench 6 , release or tighten
clamping nut 4 with wrench 5.
Clean collet and collet holder before
installation.
• Check concentricity, use only vibration free
tools and always observe M.O.S. (Max.
operating speed).
Maintenance
• Store tool in a clean, dry place.
• Disconnect tool when not in use and before
+servicing.
• The ventilator openings for cool air must be
kept free and clean, use air gun to blow out dirt.
• Replace grease in grinder every other time,
when carbon brushes are replaced. Use the
SUHNER® authorized service center nearest
you .
• Damaged plugs and cords must be replaced
rpm immediately.
5'000 • Repairs must only be done by a qualified/
6'000 licensed electrician, otherwise it could be
7'300 hazardous to the operator.
8'700 • Warranty claims can only be considered, if tool
10'000 is returned complete.
11'000
Accessories:
All accessories can be found in the SUHNER
Abrasive Power Tool catalog.
Subject to change.
AUSTRALIA
Suhner Pty. Ltd.
Abrasives and Power Tools
11, 32-34 Campbell Avenue
Dee Why 2099
N.S.W. Australia
Phone 02 9972 28 95
Fax 02 9972 28 96
http://www.suhner.com.au
SWITZERLAND:
Suhner Abrasive Expert Corp.
P.O. Box 199
CH-5201 Brugg
Phone 056/464 28 80
Fax 056/464 28 31
http://www.suhner.ch
Great Britain
Suhner (U.K.) Ltd.
Pool Road #1
Nuneaton
W arwickshire
CV 10 9AQ