Programming Functions - Key Automation 900CT-201 Manual De Instrucciones

Access the parameter menu by holding the ENTER button until the first parameter, A, appears.
Press the ENTER button repeatedly to advance through the parameters menu. To change the pa-
rameter press ↕ UP/DOWN
N.B.: any variation in function must be made with the automation closed
FUNCTIONS \ VALUES
WORKING TIME M1
(seconds)
WORKING TIME M2
(seconds)
M1 DELAY TIME
(seconds)
AUTOMATIC CLOSURE
(seconds)
OPEN COMMAND
% DECELERATION
ELECTRIC LOCK HAM-
MERING
FLASHER OUTPUT
CONDOMINIUM
(OPENING ONLY)
MOTOR WARM-UP
(minutes)
MOTOR FORCE
N° OF MOTORS
CLOSE AFTER TRANSIT
TIMER/MAGNETIC COIL
ON STEP/STEP
SOFT START
ELECTRO LOCK / SCA
(open gate light)
DEAD MAN FUNCTION
PRE-FLASHING
NB. Upon termination of displaying of parameters, you will access the total manoeuvres counter, which are shown in
two different screens where the thousands are indicated by the point lighting up. If you want to rest this counter, press
and hold button P1 and P2 until 0000 is shown
N.B. If the point of the LCD on the left lights up, it means that 10,000 manoeuvres have been exceeded, which must be
added to the value shown.
To exit parameter display, press ENTER several times until automatic closure condition is shown ( -- two dashes).

PROGRAMMING FUNCTIONS

5 6 9
5 6 9
-- 0 1
NO 5 10
Open
Open By activating the step/step function, you avoid passage of the automation in the
Stop
Close stop state. The enabled function may be critical for automations with high inertia.
close
NO 10% 20%
If you select the Hammering parameter, the control unit facilitates the release of
NO YES
Courtesy
Flashing With this selection you can select output N°9-10 as flasher or courtesy light
light
Activate the condominium function so that the first step/step impulse opens and
NO YES
NO 15 25
100%
10% Min 20%
Max
2 1
When you activate the Close After Transit function with automatic closure activated, the
NO YES
automation is closed in the shortest time possible without waiting for automatic re-closing.
When you activate the function Timer / Magnetic Coil via parameter P after terminating
total opening if step/step contact is kept closed the automatic closing time is locked
NO YES so that the gate never closes until the step/step contact is opened again, if there are
several step/step impulses during the standby time for automatic closing the time will be
When you activate the Soft Start function, during the first seconds of movement
NO YES of the automation the control unit keeps the motor at reduced speed for a softer
-- ELS SCA
When you activate the dead man function via parameter U, you can open the auto-
NO YES mation until step/step contact is closed and close the automation until contact PED is
closed; when the two contacts are released the automation goes to STOP position.
NO 1sec 2sec
12 15 18
12 15 18
With this selection you can delay start-up of the
4 10
15 20 25
When the deceleration function is activated in the last seconds
30% of operation of the automation, the control unit slows the mo-
tors based on the selected %.
the electric lock, ordering the motors to close for a short time
accepts only re-opening during closing
If you insert parameter I = from 1 to 3 and if the gate is standing
closed in standby at the end of the set time there will be a closure
of both doors of 1 min. at a value of power that does not damage
40 the motor or the mechanics. This makes it possible to keep the
internal temperature of the electric motor at a point where ice does
not form in the mechanical reduction gear. This function should be
used when temperatures of less than 5°C are expected.
30% 40% 50%
Parameter of selection of automation with 1 or 2 motors
continuously reset
The SCA function (open gate light) allows the connection of a 12Vac
signaling light, max 1W, in the electro lock output
When the pre-flashing function is activated, before any move-
4sec
ment in closing the flasher is activated for the selected time
15
21 24 27 30
21 24 27 30
second motor M1 by the set time
30 40 80 120
60% 70% 80% 90%
start.
+3sec
+3sec