Hayter Limited; Service Department; Bishop's Stortford; Hertfordshire - Murray 629108x61D Manual De Instrucciones

How To Replace the Auger Shear Bolt
The augers are secured to the auger shaft with
special shear bolts. These shear belts are de-
signed to break and protect the machine ff an
object becomes lodged in the auger housing.
Do not use a harder bolt as the protection pro-
vided by the shear bolt will be lost.
_k ARNING: For safety and to pro-
tect the machine, use only original
equipment shear bolts.
To replace a broken shear bolt, proceed as fol-
lows. Extra shear bolts were provided in the as-
sembly parts bag.
1. (Figure 2) Move the throttle control (13) to
the stop position. Disengage all controls.
2. Disconnect the spark plug wire. Make sure
all moving parts have stopped.
3. (Figure 13) Lubricate the auger shaft Zerk
fitting (1), if equipped, with a grease gun.
4. (Figure 23) Align the hole in the auger with
the hole in the auger shaft. Install the new
shear bolt (2), spacer (3), and Iocknut (4).
5. Connect the spark plug wire.
How To Prepare The Snow Thrower For
Storage
_k ARNING: Do not remove gasoline
while inside e building, near e fire,
or while you smoke. Gasoline
fumes can cause an explosion or a fire.
1. Drain the fuel tank.
2. Let the engine run until it is out of gasoline.
3. Drain the oil from the warm engine. Fill the
engine crankcase with new oil
4. Remove the spark plug from the cylinder.
Pour one ounce of oil into the cylinder. Slow-
ly pull the recoil-start grip so that the oil will
protect the cylinder. Install a new spark plug
in the cylinder.
5. Thoroughly clean the snow thrower.
6. Lubricate all lubrication points. See the Main-
tenance section.
7. Be sure that all nuts, bolts and screws are
securely fastened. Inspect all visible moving
parts for damage, breakage and wear. Re-
place if necessary.
8. Cover the bare metal parts of the blower
housing, auger, and the impeller with spray
rust preventative lubricant.
9. Put the unit in e building that has good ven-
tilation.
10. If the machine must be stored outdoors,
block up the snow thrower to be sure the en-
tire machine is off the ground.
11. Cover the snow thrower with a suitable pro-
tective cover that does not retain moisture.
Do not use plastic.
How To Order Replacement Parts
The replacement parts are shown either on the
back pages of this Instruction Book or in a
separate Parts List Book.
Use only manufacturer's authorized or approved
replacement parts. The letter placed on the end
of the part number denotes the type of finish for
the part, C for chrome, Z for zinc, a PA for
purchased assembly. It is important that you
include this when ordering a part. Do not use
attachments or accessories not specifically
recommended for this unit. In order to obtain
ENGLISH
proper replacement parts you must supply the
model number (see nameplate).
Replacement parts, except for the engine,
transmission, transaxle or differential, are
available from the store where the product was
purchased, a service shop recommended by the
store or from a "Murray, Inc. Central Parts
Distributor" listed on the back page of this
Instruction Book.
If you are unable to obtain parts or service in the
manner outlined above, then contact:
HAYTER LIMITED,
Service Department,
Spellbrook,
Bishop's Stortford,
Hertfordshire. CM23 4BU.
MURRAY, INC.
International Sales
P.O. Box 268
Brentwoed, Tennessee USA 37024
1-800-251-8007
Fax (615) 373-8633 Collect telephone calls will
not be accepted.
Replacement parts for the engine, transaxle, or
transmission, are available from the
manufacturer's authorized service centre found
in the yellow pages of the telephone directory.
Also, see the iedividual engine or transmission
warranties to order replacement parts.
When ordering the following information is
required:
(1) The Model Number
(2) Serial Number
(3) Part Number
(4) Quantity
TROUBLE SHOOTING CHART
TROUBLE
Difficult starting
CAUSE
Defective spark plug.
Water or dirt in fuel system.
Unit fails to discharge snow
Engine runs erratic Blocked fuel line, empty gas tank, or stale
gasoline
Engine stalls Unit running on CHOKE.
Engine runs erratic; Water or dirt in fuel system.
Loss of power
Excessive vibration Loose parts: damaged impeller
Unit fails to propel itself Drive belt loose or damaged.
Incorrect adjustment of traction drive cable
Worn or damaged friction wheel
Auger drive belt loose or damaged.
Auger control cable not adjusted correctly.
Shear bolt broken
Discharge chute clogged.
F-031065L
Foreign object lodged in auger
17
CORRECTION
Replace spark plug.
Use carburetor bowl drain to flush and refill with
fresh fuel,
Clean fuel line; check fuel supply; add fresh
gasoline
Set choke lever to RUN position,
Use carburetor bowl drain to flush and refill with
fresh fuel,
Stop engine immediately and disconnect spark
plug wire. Tighten all bolts and make all
necessary repairs. If vibration continues, have
the unit serviced by e competent repairman.
Replace drive belt.
Adjust traction drive cable,
Replace friction wheel,
Adjust auger drive belt; replace if damaged.
Adjust auger control cable,
Replace shear bolt
Stop engine immediately and disconnect spark
plug wire, Clean discharge chute and inside of
auger housing,
Stop engine immediately and disconnect spark
plug wire, Remove object from auger.