Kinderkraft EVOLUTION Manual De Usuario página 19

II FOLDING THE BABY STROLLER FRAME, MOUNTING AND DISMOUNTING THE WHEELS
Place the frame (A) on a flat surface. Unlock the lock on the left side of the baby stroller, grasp the parent's handlebar
and lift the frame up (Fig. 1), the frame should lock. Then mount the front wheels (B) (Fig. 2, A) and rear wheels (C) (Fig.
2, B) until you hear a distinctive click sound.
The buttons for dismounting the front and rear wheels are marked in Fig. 2, A and Fig. 2, B
WARNING! Before using the buggy, make sure that all the
wheels are properly installed.
III MOUNTING THE CARRYCOT
ATTENTION: There are grey straps on the sides of the carrycot and on the frame of the baby stroller, which improve
the safety of the correctly mounted seat.
ATTENTION! When mounting the carrycot, the seat must be mounted in such a way that it faces the parent!
The first step is to unfasten the seat from the baby stroller frame. To do this, lift the lever on top of the backrest and
adjust the backrest to the seat so that the grey stripes form a single line (Fig. 3), then slide the seat out of the baby stroller
frame, then turn the seat forward to the parent and slide the seat onto the frame, keeping the grey stripes in place (Fig.
4). Lower the backrest to the lowest level with the lever and lift the footrest up (Fig. 5). Place the soft carrycot (E) on the
seat (no need to unfasten the straps from the seat) and then clip the straps from the carrycot under the seat. ATTENTION!
There are loops around the canopy, through which the straps must be pulled to stabilize the carrycot (Fig. 6).
WARNING! THE BASSINET CAN ONLY BE MOUNTED FACING
BACKWARDS (the child faces the person pushing the buggy).
IV ASSEMBLY/DISASSEMBLY OF THE ARMREST, CANOPY, FOOTREST COVER AND CUP HOLDER
Once the soft carrycot has been removed, mount the armrest (D) by sliding it into the guides on the sides of the frame,
as shown in Fig. 7, A. The armrest can be removed by pressing the buttons on its sides (Fig. 7, B).
The canopy (F) is mounted by sliding its ends into the guides located in the frame of the baby stroller, as shown in figure
8, and then the back of the canopy is fixed to the straps and velcro on the backrest. The canopy can be adjusted in several
positions. The canopy is dismantled by pushing the buttons and ejecting the canopy (Figure 9).
Place the footrest cover (G) on the seat and fasten it with the clips.
To install the cup holder (I), slide it on the pin protruding from the frame (Fig. 10).
V INSTALLATION OF THE MOSQUITO NET AND RAIN COVER
Put the mosquito net on the seat and secure it with the straps at the back of the seat (Fig. 11).
Put the rain cover on the seat and secure it with the straps on the sides of the seat.
VI USING THE BRAKE
The baby stroller is equipped with a foot brake on the rear axle. Press the pedal to activate the brake. Unlock by lifting
the pedal up (Fig. 12).
VII ADJUSTMENT OF THE BACKREST, FOOTREST AND PARENT'S HANDLEBAR
It is possible to adjust the baby stroller backrest in 3 different positions (Fig. 13). To do this, pull the lever on top of the
backrest and place it in a position comfortable for the child. The backrest locks automatically. ATTENTION! The seat in
the baby stroller version can be installed both backwards and forwards to the parent.
The footrest can be adjusted in 4 positions (Fig. 14). Press the buttons on both sides of the footrest at the same time and
set it to the desired position.
The parent's handlebar is adjusted by pressing the button in the middle of the handlebar and pulling the handlebar up
or down. You can adjust the handle height to one of 4 different levels (Fig. 15).
VIII FOLDING THE BABY STROLLER
Attention! The baby stroller cannot be folded when the carrycot is mounted!
The baby stroller can be folded in two ways:
• Seat mounted backwards to the parent - set the backrest in position 1 and raise the seat and footrest as much as
possible for easy access to the folding mechanism under the seat (Fig. 16). To fold the baby stroller, move the button
on the mechanism, turn the folding mechanism according to the arrow and lift the mechanism up (Fig. 18). The baby
stroller will fold and the lock on the left side of the frame will prevent the baby stroller from unfolding again.
• Seat mounted forward to the parent - adjust the backrest as shown in figure 17 and then fold the baby stroller as
shown in figure 18.
IX REMOVING THE SEAT COVER
To start removing the cover, remove the canopy. In the next step, remove the cover from the hooks on the sides of the
seat and the Velcro under the seat and under the footrest. Push the crotch strap buckle in the bottom of the seat through
the hole. Remove the cover by pulling it from the backrest
19