Makita 8270D Manual De Instrucciones página 4

ENGLISH
(Original instructions)
1 Button
2 Battery cartridge
3 Switch trigger
4 Reversing switch lever
5 Low speed
6 High speed
SPECIFICATIONS
Model
Capacities
Steel .............................................................10 mm
Wood ............................................................25 mm
Concrete.......................................................8 mm
Wood screw..................................................5.1 mm x 63 mm
Machine screw .............................................6 mm
–1
No load speed (min )
High ..............................................................0 – 1,200
Low...............................................................0 – 350
–1
Blows per minute (min
High .............................................................0 – 18,000
Low ..............................................................0 – 5,250
Overall length ..................................................214 mm
Net weight .......................................................1.6 kg
Rated voltage ..................................................D. C. 12 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications and battery cartridge may differ from
country to country.
• Weight, with battery cartridge, according to EPTA-Pro-
cedure 01/2003
Intended use
The tool is intended for impact drilling in brick, concrete
and stone as well as for drilling without impact in wood,
metal, ceramic and plastic.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
CORDLESS HAMMER DRIVER DRILL SAFETY
WARNINGS
1. Wear ear protectors with impact drilling. Expo-
sure to noise can cause hearing loss.
2. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
3. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
4
Explanation of general view
7 Speed change lever
8 Action mode changing ring
9 Arrow
10 Graduations
11 Adjusting ring
12 Sleeve
8270D
)
8280D
10 mm
25 mm
10 mm
5.1 mm x 63 mm
6 mm
0 – 1,200
0 – 350
0 – 18,000
0 – 5,250
214 mm
1.7 kg
D. C. 14.4 V
4. Hold power tool by insulated gripping surfaces,
when performing an operation where the fas-
tener may contact hidden wiring. Fasteners con-
tacting a "live" wire may make exposed metal parts
of the power tool "live" and could give the operator
an electric shock.
5. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
ENE039-1
high locations.
6. Hold the tool firmly.
7. Keep hands away from rotating parts.
8. Do not leave the tool running. Operate the tool
only when hand-held.
GEA010-1
9. Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
10. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
SAVE THESE INSTRUCTIONS.
GEB056-4
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.
13 Ring
14 Tighten
15 Blow-out bulb
8390D
13 mm
36 mm
13 mm
6 mm x 75 mm
6 mm
0 – 1,200
0 – 350
0 – 18,000
0 – 5,250
239 mm
2.2 kg
D. C. 18 V