Peg-Perego SI Instrucciones De Uso página 11

making sure that the side clips are correctly fastened (fig_c).
2 If the clips are not properly fastened, push down on the seat (fig_a) until it clicks into place. Finally,
press down with your foot on the word PUSH (fig_b).
3 BASKET: To fit the basket, pull the loops over rear hooks A and B and front hook C (fig_a).
CUP HOLDER: It can only be fitted to the right hand side of the stroller, using the clip which is
already present on the chassis. To fit the cup holder, push until it clicks into place (fig_b).
4 HANDLE ADJUSTMENT: The handles can be set at 3 different heights. To move them into the
required position, press the button and simultaneously pull the handle upwards. To lower them,
press the button and push the handle down (fig_a).
BRAKE: To set the brake on the stroller, lower the lever on the rear wheel unit with your foot. To
release the brake, lift the lever (fig_b). When stationary, always apply the brake.
5 SWIVEL WHEELS: The wheels are already fitted to the stroller.
To make the front wheels swivel, lower the lever (fig_a). To keep them fixed, lift the lever (fig_b).
The rear wheels do not swivel.
6 HOOD: To fit the hood, click the fasteners onto the appropriate points and button down the hood
on the rear of the stroller's backrest (fig_a).
The hood can be set in 3 different positions (fig_b) by simply pulling it forwards or backwards.
The section of netting can be pulled out from the hood to protect the child from the sun (fig_c)
and easily replaced back inside when it is no longer needed.
7 COVER: To fit the cover correctly (fig_a), fasten the buttons inside the stroller (fig_1) and place it
underneath, covering the leg rest and fastening the buttons (fig_2).
RAIN CANOPY: To fit the rain canopy, slip it onto the stroller (fig_b), button it down on the sides of the
hood (fig_1) and attach the elastic loops, taking in the chassis in the lower part of the stroller (fig_2).
8 FIVE POINT SAFETY HARNESS: Equipped with joined shoulder straps and crotch straps. To fasten
the safety harness, insert the two waist strap buckles (with the shoulder straps attached) into the
leg divider strap until you hear a click (fig_a). To release it, press both sides of the buckle and pull
the waist strap outwards at the same time (fig_b).
 It is possible to set the safety harness at 2 different heights, depending on how tall the child is.
When the child is bigger, it is necessary to switch to the higher position (number 2).
1 0 To change the position of the safety harness, it is necessary to:
_ release the two buckles on the rear of the backrest, firmly pulling the straps (fig_a).
_ remove the harness from shoulder strap 2 (fig_b).
_ remove shoulder strap 2 (fig_c) and insert it in slot 1 from behind (fig_d).
_ place shoulder strap 1 in the upper slot (fig_e).
_ place shoulder strap 2 in the upper slot, passing it through from behind (fig_f).
_ fasten the two buckles behind the backrest once again (fig_g).
1 1 To tighten the vertical and waist straps, pull in the direction of the arrow on both sides (fig_a). To
loosen them, do the opposite. The waist strap can be tightened as far as the safety stop (fig_b).
1 2 LEG REST ADJUSTMENT: The leg rest can be set in 2 different positions. To lower the leg rest, pull
the two side levers downwards and at the same time lower the leg rest. To raise the leg rest, push
it upwards until it clicks into position.
BACKREST ADJUSTMENT: The backrest can be set in 3 positions: To lower the backrest, lift the
levers on both sides at the same time and lower it, locking it in the position required. To lift the
backrest, push it upwards.
1 3 FOLDING UP: To fold up the stroller, lower the release lever on the right hand side (fig_a) until it
clicks and pull the central folding handle upwards (fig_b). Make sure it is folded up properly by
checking that the lever on the left is fastened. When it is folded up, it is freestanding (fig_c).
SI_NA_FINA0801I101.indd 11
- 11 -
16-01-2009 9:02:14