Assembly Of The Milling Machine; Mounting On Lathe Pd 230/E; Mounting Of Milling Machine On Kt; Working With The Milling Device - Proxxon PF 230 Manual De Instrucciones

PF 230 milling machine technical data
Voltage:
Power rating:
Short-term operation
6 spindle speeds by shifting the V-belt:
280, 550, 870, 1200, 1500 and 2200 rpm
Sleeve stroke
Vertical adjustment travel
Noise emission
Vibration
Dimensions
Weight
Only for operation in closed
rooms.
KT 230 compound-type table technical
data
Work area:
Adjustment travel in X direction: 170 mm
Adjustment travel in Y direction: 60 mm
Weight:
Dimensions of T-grooves:
Groove spacing:
Feed per rotation:
Feed per graduation line:
Please do not dispose off the machine!

Assembly of the milling machine

Mounting on lathe PD 230/E

1. Mounting lathe on a firm base.
2. Attach the mounting block 1 (Fig. 5) to the lathe 3 using
screws 2 (Do not tighten screws yet!)
3. Tighten screw 3 (Fig. 6) and insert in pillar 1.
4. Tighten screw 4 to clamp the pillar.
5. Attach the milling table 3 (Fig. 7) to the lathe support
using screws 2 and square nuts 1.
Mounting of milling machine on KT 230 compound-type
table
Safe and precise operation is only possible if the machine
is properly fastened to a stable work surface.
1. Attach compound-type table to work surface using 4
screws 1 (M4, not included) (Fig. 8).
2. When working in conjunction with the PROXXON
PF 230 milling machine, insert pillar in flange and clamp
using screws 2.
220 – 240 volts, 50/60 Hz
140 watt
10 min.
30 mm
200 mm
70 dB(A)
2.5 m/s 2
refer to Fig. 3
approx. 9 kg
270 mm x 80 mm
9.5 kg
refer to Fig. 4
25 mm
1.5 mm
0.05 mm
Note:
The middle screw (between the two locking screws) is a
spreader screw. By tightening this screw, the opening can
be widened slightly, making it easier to insert the column.
Before clamping the column, do not forget to loosen this
screw again!

Working with the milling device

Important!
Disconnect the mains plug before making any adjustments
on the milling machine!
The milling spindle on the PF 230 may be adjusted in
height in 2 ways (Fig. 9):
1. Using the fine tolerance feed 1
2. Using the drill lever 2

Height adjustment via fine tolerance feed

1. Loosen screw 3 (Fig. 9).
2. Adjust to the desired height using the hand wheel 1
(1 rotation corresponds to 1 mm feed).
3. Screw 3 must always be tightened again.

Feed via drill lever

1. Loosen screw 4 (Fig. 9).
2. Loosen screw 6 and set scale 5 to zero.
Retighten screw 6.
3. Adjust to the desired height using the drill lever 2.
4. Retighten screw 4.
The drill lever can be used for height adjustment as well as
for drilling. When drilling, do not tighten screw 4.

Spindle fine feed item no. 24140

When using this accessory, there is the option of effecting
spindle feed via the drill lever or by turning the handwheel
1 (Fig. 9a).
The handwheel is fitted with a moveable scaling ring: This
can be set to "0" for adjusting the required feed simply and
exactly.
When the handwheel is turned, this produces a spindle
feed of 1.5 mm.
Fitting the fine feed is simple:
1. Insert the shaft on the fine feed into the drill hole for the
drill lever shaft on the milling cutter. During assembly, it
is essential to observe the following: The "spring" on the
fine feed 2 fits into the slot on the drill lever shaft 3.
2. Align the fine feed and secure it with the screw provided.
3. You can now switch the fine feed on or off with the
coupling shaft. To switch on, press your finger on the
shaft (4) and turn the handwheel at the same time.
Note:
- 9 -