Connection To Mains - Tecfrigo SNELLE’ 350 Serie Manual De Instalacion Y Uso

9. CONNECTION TO MAINS

1 . Ensure that mains voltage and frequency are the same as those stated on the rating plate ( )
attached to the appliance.
properly earthed. It is appropriate for the nominal current as set out on the rating plate.
>
-
with the IEC regulations: Magneto-thermic differential switch with In = nominal value as stated on the
-
rating plate; Differential with Id sensitivity = 30 mA.
in the room. 4 . The connecting cable to the appliance is H05 VVF, designed for internal use only. For
different setting it is necessary to change it (for example H07 VVF for external settings)
the appliance, during the trasport or storage, has been erroneously placed in horizontal position or
upside-down, it must be left in the correct position for at least 3 hours before connecting it to the
electrical supply. 5 . Insert the plug (do not use triple and reduction outlets) (see picture 8).
10. CONTROLS
The controls of the appliance are situated at the front inside a protected recess. .
run the rotating shelves. The rotation stops immediately when opening the door or if encountering even a
2 Light switch:
slight obstruction. .
to run the refrigeration system.
adjust the temperature inside the appliance. In order t
5 "SET" the display will show the temperature of the cell, pushing several times the button
temperature increases while pushing several times the button
(see picture 9).
11. CHECKING THE CORRECT FUNCTIONING
MAKE SURE THAT: 1 . T he plug is connected
thermometer shows the desired temperature for the foodstuffs to be stored in. . Internal light and
rotation switches are on. . The door is closed. . The appliance is not exposed to the direct light of the 5
sun or to high powered lamps. . The room temperature does not exceed that in which the appliance is
designed to work normally, i.e. +30° C 55% r.h.
are free from obstruction for at least 30 cm.
in order to ensure a good circulation of the cool air, especially between the rear glass panel and the
shelves, where the air outlets are
12. INTERNAL CLEANING (EVERY 15 DAYS)
1 .Switch off electricity supply. . Open the door and remove the dislpayed foodstuffs. . Wipe the internal
surfaces and the accessories of the appliance with a sponge dipped in water with a little bicarbonate of
soda.Dry with care.
13. REPLACEMENT OF INTERNALIGHT
1 . Switch off electricity supply. . Unscrew the screws fixing the upper light holder. . Detach the
fluorescent tube from the upper lamp holder. . Remove the tube from the lower lamp holder. . Remove
the transparent protective tube. . Replace the fluorescent tube. . Replace everything in reverse order
(see picture 10).
14. REPLACEMENT OF THE DOOR MAGNETIC GASKET
1 .Open the door. 2. Take hold of the magnetic gasket with your hands and remove it from the frame.
3 . Insert the new gasket and press all around it when in place
Operator's guide
2. Ensure that the supply socket has the following characteristics:
to switch on the light inside the appliance.
4. Termometer: to read the temperature in the appliance.
. 2 . Refrigeration unit switch is on(green light lit up). . The
6
7
(climatic class 4).
9. The foodstuffs are placed on the shelves in the right way,
(max 6 kgs for each shelf)
2
2
4
6
7
3 . Ensure that there is no danger of explosion (AD)
3. Refrigeration switch:
o adjust the temperature: pushing once the button
7 "DOWN" the temperature decreases
4
8 . The compressor ventilation grilles
.
7
(see picture 11).
A
It is
=
It complies
?
Notice: in case
1 Rotation switch: to
Thermostat: to
6 "UP" the
3
3
3
5
I
UK
D
E
F
NL
P
S
DK
FIN
B
GR
CZ
EE
LV
LT
H
M
PL
SK
SLO