Cleaning And Maintenance - Moulinex zelio Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 20

CLEANING AND MAINTENANCE

1. C
HANGING THE BAG
• The bag capacity indicator (5) tells you
when the bag is full or saturated.
If you notice that your vacuum cleaner is
less efficient, select the maximum power
and by lifting the floor head off the floor. If
the indicator remains red, replace the
bag.
• Open the lid (9) of your vacuum cleaner
fig. 13
.
• Withdraw the bag support (16)
Unclip the bag (18) by pressing the lever
fig. 15
, and dispose of the bag in a waste
- fig. 16
bin
.
• Fit a fresh bag, position it using the tongue
provided and clip it onto the bag support
- fig. 17
. Slide the bag support back onto
- fig. 18
the runners
- fig. 19
the compartment
• Make sure that the bag is in the correct
position before closing the lid (9).
2. C
LEANING THE FOAM FILTER FOR PROTECTION
OF THE MOTOR
• The motor foam-filter protection (12) must
always be in place when in use.
• Open the lid (9). The grid (13)
then remove the foam-filter (12)
• Shake it and clean it, every ten dustbag
changes, with tepid soapy water.
• Rinse, dry and put it back in place.
• Let the foam-filter dry (12) completely
before putting back in place.
Caution : N.B. Make sure that the foam filter
is completely dry before fitting it again.
3. C
HEPA*
HANGE THE
*
MICROFILTER
ON EVERY TENTH CHANGE OF
BAG
3.1- The Hepa* filter cassette
• Open the lid (9) of your vacuum cleaner
fig. 13
.
• Remove the Hepa* filter cassette (14)
fig. 22
and dispose of the cassette in a
waste bin.
• Fit
the
new
Hepa*
(ref. MT0001 01) (14) in its compartment
fig. 23
.
• Check that the Hepa* filter cassette (14) is
fitted correctly before re-closing the lid (9).
-
- fig. 14
;
-
place the bag inside
.
- fig. 20
- fig. 21
.
FILTER CASSETTE OR THE
-
-
filter
cassette
-
3.2- The microfilter cassette*
• Open the lid (9) of your vacuum cleaner
fig. 13
.
• Withdraw the microfilter cassette* (15)
fig. 22.
• Separate the grey foam filter (15b) from
the microfilter (15a).
• Dispose of the microfilter (15a) in a waste
bin and replace it with a new Microfilter
(ref. MT0001 01).
• Wash the grey foam filter (15b) with warm
soapy water (mild detergent). Squeeze it
out and leave it to dry for at least 12 hours.
Caution: Make sure that the grey foam
filter is completely dry before putting it
back in place.
• Re-fit the grey foam filter (15b) to the
microfilter (15a).
• Re-fit the microfilter cassette* in its
- fig. 23
compartment (15)
• Check that the microfilter cassette* (15) is
fitted correctly before re-closing the lid (9).
4. C
LEAN THE VACUUM CLEANER
• Clean the housing of the vacuum cleaner
with a soft and humid rag and let dry.
• Clean the cover with a dry rag
• Do not use abrasive or aggressive
products.
F
GB
I
-
E
-
P
SA
FA
TR
.
- fig. 24
.
11

Publicidad

Tabla de contenido
loading

Tabla de contenido