Functional Description - Makita AN924 Manual De Instrucciones

FUNCTIONAL
DESCRIPTION
CAUTION:
Before adjusting or checking func-
tion on the tool, always release the trigger and
disconnect the air hose from the tool.
Adjusting depth of nailing
CAUTION:
Always release the trigger and
disconnect the hose before adjusting the depth
of nailing.
Fig. 5 : 1. A d j uster
T o a d j ust t h e d ept h o f nailing, turn t h e a d j uster.
T h e d ept h o f nailing is t h e d eepest w h en t h e a d j uster
is turned fully in the A direction shown in the figure. It
w ill be c ome s h allo w er as t h e a d j uster is turne d in t h e B
d ire c tion.
I f nails c annot be d ri v en d eep enoug h e v en w h en t h e
a d j uster is turne d f ull y in t h e A d ire c tion, in c rease t h e
air pressure.
I f nails are d ri v en too d eep e v en w h en t h e a d j uster is
turne d f ull y in t h e B d ire c tion, d e c rease t h e air pressure.
G enerall y speaking, t h e tool ser v i c e li f e w ill be longer
w h en t h e tool is use d w it h lo w er air pressure an d t h e
a d j uster set to d eeper d ept h o f nail d ri v ing.
Hook
CAUTION:
Always release the trigger and
disconnect the hose before changing the hook
position.
CAUTION:
Never hook the tool at high loca-
tion or on potentially unstable surface.
CAUTION:
Do not hang the hook from the
waist belt. I f t h e nailer a c c i d entall y d rops, it ma y
result in misfiring and personal injuries.
Fig.6
Fig.7: 1. H ook 2. H e x so c ket bolt 3. H ole
T h e h ook is c on v enient f or h anging t h e tool temporaril y .
T o c h ange t h e h ook position, remo v e t h e h e x so c ket
bolt an d s w it c h t h e h ook d ire c tion. T h e h ook h as t w o
h oles. C h oose t h e h ole d epen d ing on y our pre f erable
h ook w i d t h .
ASSEMBLY
CAUTION:
Before carrying out any work on
the tool, always release the trigger and discon-
nect the air hose from the tool.
CAUTION:
Load the same type, size and
uniform length of nails when loading nails in the
magazine.
Loading nailer
1. S li d e t h e pus h er le v er until it is lo c ke d at t h e mag-
a z ine en d .
Fig.8: 1. P us h er le v er
2. I nsert a strip o f nails into t h e slit in t h e rear o f t h e
magazine and push the strip toward the firing opening.
Fig.9: 1. S trip o f nails 2. Maga z ine
3. P ress t h e lo c k le v er w h ile sli d ing t h e pus h er le v er
to w ar d t h e maga z ine en d .
Fig.10: 1. P us h er le v er 2. L o c k le v er
4. R eturn t h e pus h er le v er.
Do not put your nger on the rail
CAUTION:
of the pusher lever. D oing so ma y c ause personal
injury by the pusher lever swiftly returns to the firing
opening.
Fig.11
Correct loading of the nails
CAUTION:
Be sure to load nails in the correct
direction.
Be sure to loa d t h e nail at t h e c orre c t angle. Nails w ill be
parallel w it h t h e d ri v er gui d e i f c orre c tl y set.
Fig.12
W h en loa d ing t w o or more strips o f t h e nails, set t h e
nail h ea d o f t h e latter strip properl y o v erlaps t h at o f t h e
f ormer strip.
Fig.13
A l w a y s set t h e lo c k o f t h e pus h er le v er to h ol d t h e nail
h ea d as illustrate d .
Fig.14: 1. L o c k o f t h e pus h er le v er
Connecting air hose
Do not rest your nger on the
CAUTION:
trigger when connecting the air hose.
Fig.1 5 : 1. Air fitting 2. A ir so c ket
Slip the air socket of the air hose onto the air fitting on
the tool. Be sure that the air socket locks firmly into
position when installed onto the air fitting.
A h ose c oupling must be installe d on or near t h e tool in
su c h a w a y t h at t h e pressure reser v oir w ill d is c h arge at
t h e time t h e air suppl y c oupling is d is c onne c te d .
OPERATION
CAUTION:
Make sure all safety systems are in
working order before operation.
10 ENGLISH