Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 14

Troubleshooting

(For further information, visit the mgeops.com site or contact after-sales support.)
Problem
1
The battery backup outlets 9
are not supplied with power.
2
The connected devices are not
supplied when AC power fails.
3
AC power is available, but the
UPS operates on battery power.
4
The filtered outlets 8 are not
supplied.
5
Green button 13 flashes
frequently and audio alarm
beeps.
6
Red LED 12 is on and the
audio alarm beeps every 30
seconds.
7
Red LED 11 is on and the
audio alarm beeps every 30
seconds.
8
Green LED 10 is off and the
filtered outlets 8 are supplied.
9
The telephone line is disturbed
or modem access is not possible.
10
Red LED 11 flashes.
Advanced customizing of your UPS:
Sensitivity to variations of the AC power supply
Only to be used if frequent switching to the UPS battery
due to large variations in the AC supply voltage.
Accessing the programming mode: with the device
switched off, press button 13 for 6 s and release it once
LEDs 11 12 13 have come on.
Display of the 3 possible voltage ranges according to the
status of LEDs 11 and 12 :
Normal mode
Extended
(factory
mode:
configuration):
AC supply
AC supply
between 150V
between 165V
and 285V
and 285V
12
12
11
11
13
13
Change from one mode to another by
successively pressing button 13 .
Memorizing the mode: 10 s after the last press of the
button.
Diagnostic
Button 13 is not lighted on.
The devices are not connected to
the battery backup outlets 9 .
Circuit breaker 14 , located under
the UPS, has been tripped by an
overload on the UPS output.
The wall outlet is not supplied.
Circuit breaker 14 , located under
the UPS, has been tripped by an
overload on the UPS output.
The UPS frequently operates on
battery power because the AC power
source is of poor quality.
The UPS battery backup outlets 9
are overloaded.
A fault has occurred on the UPS.
The battery backup outlets 9 are no
longer supplied.
Surge protection is no longer
provided.
Surge protection on the telephone
line is no longer provided.
The battery has reached the end of
its service life.
Audio alarm
Possibility of deactivating the audio alarm when the UPS
is operating on the battery.
Accessing the programming mode: with the device
switched off, press button 13 for 11 s and release it once
the audio alarm sounds.
Display of the 2 possible audio alarm modes:
Sensitive mode:
Normal mode (factory
AC supply
configuration):
between 175V
the UPS emits a beep every
and 285V
10 s when operating on its
battery.
12
11
13
Memorizing the mode: 5 s after the last press of the
button.
Solution
Press button 13 and check that it
turns green.
Connect the devices to the battery
backup outlets 9 .
Disconnect excess equipment and
reset the circuit breaker 14 by
pressing the corresponding button.
Supply power to the wall outlet.
Disconnect excess equipment and
reset the circuit breaker 14 by
pressing the corresponding button.
Have the electrical installation
checked by a professional or use
another wall outlet.
Disconnect excess equipment
connected to the battery backup
outlets 9 .
Call after-sales support.
Call after-sales support.
Disconnect the telephone line from
the wall outlet.
Call after-sales support.
Have the battery replaced.
Normal mode
activated:
programming by
continuous beep.
Change from one mode to another by
successively pressing button 13 .
Silent mode:
the UPS emits a single
beep when switching to
battery operation and then
remains silent.
Silent mode
activated:
programming by
a beep every
second.
MAU-00033/AD - 7

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ellipse max850Ellipse max1100Ellipse max1500

Tabla de contenido