Return Authorization - Bullard CAB Serie Manual De Usuario

wArning
Removing the front of the housing by prying at the top will result in damage to the
housing. This damage is not covered under warranty.
Sensor replacement
nOTE
Important: Before installing a replacement sensor, verify
that you have the correct sensor. The CABRS is the
replacement sensor for all COM10 or COM5 monitors
with serial numbers with a suffix "A", and serial numbers
with NO suffix. The CABRS2 is the replacement sensor for
Battery
Cover
Screws
Fig. 6
Pry here
Gently pull out the old sensor.
Remove the shorting clip cover from the new sensor.
Failure to remove shorting clip (not shown) will result in inability to calibrate.
Fig. 7
30 minutes. The new sensor must be zeroed and calibrated before first use. See Zero
Point Adjustment and Calibration Instructions.
One Year Limited warranty
Bullard warrants to the original purchaser that the Clean Air Box will be free
of defects in material and workmanship under normal use and service for a
period of one (1) year from the date of purchase. Bullard's obligation under
this warranty is limited to repairing or replacing, at its option, articles that
are returned within the warranty period and that are, after examination,
Fig. 5
CABrS
all COM10
or COM5
CABrS2
monitors with
serial numbers with a suffix
"B". Also, the monitors that
require the CABRS2 will have
an extra board to which the
sensor mounts (Figure 5).
The sensor is easily accessible by
removing the front of the housing
from the COM5 or COM10 monitor.
To gain access to the sensor,
remove the four screws on the
front of the CO monitor only. After
removing the four screws, gently
pry the front of the housing off from
the bottom of the housing. (Figure 6)
Align pins and gently push
the new sensor into the
sockets (Figure 7).
Replace the front cover of
the monitor when sensor
replacement is complete.
Ensure LED lights are
aligned with housing before
securing front cover with
screws.
After replacing the sensor,
allow the instrument to
warm up for at least
www.bullard.com
Clean Air Boxes (CAB) Series
shown to Bullard's satisfaction to be defective, subject to the following
limitations.
a) Clean Air Box must be returned to the Bullard factory with shipping
charges prepaid.
b) Clean Air Box must not be altered from its original factory configuration.
c) Clean Air Box must not have been misused, subjected to negligent use, or
damaged in transport.
d) The date of purchase is within the one year warranty period. (A copy of
the purchaser's original invoice showing the date of purchase is required
to validate warranty coverage.)
In no event shall Bullard be responsible for damages for loss of use or other
indirect, incidental, consequential or special costs, expenses or damages
incurred by the purchaser, notwithstanding that Bullard has been advised of
the possibility of such damages.
ANY IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED IN DURATION TO ONE (1) YEAR FROM THE DATE OF PURCHASE OF
THIS PRODUCT.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or allow limitations on how long an implied warranty
lasts, so the above limitations or exclusion may not apply to you. This
warranty gives you specific legal rights, and you may have other rights which
vary from state to state.

return Authorization

The following steps must be completed before Bullard will accept any
returned goods. Please read carefully.
Follow the steps outlined below to return goods to Bullard for repair or
replacement under warranty or for paid repairs:
1. Contact Bullard Customer Service by telephone or in writing at:
E.D. Bullard Company
1898 Safety Way
Cynthiana, KY 41031-9303
Toll-Free: 877-BULLARD (285-5273)
Phone: 859-234-6616
In your correspondence or conversation with Customer Service, describe
the problem as completely as possible. For your convenience, the
representative will try to help you correct the problem over the phone.
2. Verify with your representative that the product should be returned to
Bullard. Customer Service will provide you with written permission and a
return authorization number.
3. Before returning the product, decontaminate and clean it to remove
any hazardous materials which may have settled on the product during
use. Laws and/or regulations prohibit the shipment of hazardous or
contaminated materials. Products suspected to be contaminated will be
professionally discarded at the customer's expense.
4. Ship returned products, including those under warranty, with all
transportation charges pre-paid. Bullard cannot accept returned goods on
a freight collect basis.
5. Returned products will be inspected upon return to the Bullard facility.
Bullard Customer Service will telephone you with a quote for required
repair work which is not covered by warranty. If the cost of repairs
exceeds stated quote by more than 20%, your representative will call you
for authorization to complete repairs.
User Manual
5