Numax SFL618 Manual Del Usuario página 3

MODEL:SFL618
TOOL USE AND CARE
Know this tool. Read manual carefully, learn its
applications and limitations, as well as the specific
potential hazards related to this tool.
Use only fasteners that are recommended for
your models. Do not use the wrong fasteners or
load the fasteners incorrectly.
Check for misalignment or binding of moving
parts, breakage of parts, and any other
condition that may affect the tool's operation.
If damaged, have the tool serviced before using.
Many accidents are caused by poorly maintained
tools.
Maintain tools with care. Keep tool clean. A
properly maintained tool, reduces the risk of
binding and is easier to control.
Store tools out of the reach of children and
other untrained people. Tools are dangerous in
the hands of untrained users.
Check operation of the tool before use.
Do not force tool. Use the correct tool for your
application. The correct tool will do the job better
and safer at the rate for which it is designed.
Use clamps or another practical way to
secure and support the workpiece to a stable
platform. Holding a tool by hand or against the
body is unstable and may lead to loss of control.
Keep the tool and its handle dry, clean and
free from oil and grease. Always use a clean
cloth when cleaning. Never use brake fluids,
gasoline, petroleum-based products, or any
strong solvents to clean your tool.
Do not use the tool as a hammer.
Never use this tool in a manner that could
cause a fastener to be directed toward
anything other than the workpiece.
Always carry the tool by the handle. Never
carry the tool by the air hose.
Do not use the tool if it leaks air or does not
function properly.
Do not operate the tool if it does not contain a
legible warning label.
TOOL SERVICE
Use only accessories that are identified by the
manufacturer for the specific tool model.
Use of unauthorized parts or failure to follow
maintenance instructions may create a risk of
injury.
Use only the lubricants supplied with the tool
or specified by the manufacturer.
Tool service must be performed only by
qualified repair personnel.
04
.
HTTP://WWW NUMAXTOOLS COM
OPERATION
Do not drive fasteners near edge of material.
The workpiece may split causing the fastener or
ricochet, injuring you or people around.
Do not drive fasteners on top of other
fasteners or with the tool at an overly steep
angle as this may cause deflection of
fasteners which could cause injury.
Do not actuate the tool unless you intend to
drive a fastener into the workpiece.
Always handle the tool with care:
◆Respect the tool as a working implement.
◆ Never engage in horseplay.
◆Keep others a safe distance from the tool
while tool is in operation as accidental
actuation may occur, possibly causing injury.
AIR SUPPLY AND CONNECTIONS
The connector on the tool must not hold
pressure when air supply is disconnected.
incorrect fitting is used, the tool can remain
charged with air after disconnecting and thus will
be able to drive a fastener even after the air line is
disconnected, possibly causing injury.
Do not use oxygen, combustible gases or
bottled gasses as a power source for this tool.
Explosion may occur, causing injury or death.
Do not connect with an air compressor which
can potentially exceed 200 Psi.
As tool may burst, possibly causing injury.
Always disconnect air source:
◆Before making adjustments.
◆When servicing the tool.
◆When clean a jam.
◆When tool is not in use.
◆When moving to a different work area, as
accidental actuation may occur, causing injury.
LOADING TOOL
Do not load the tool with fasteners when any
one of the operating controls is activated.
Never place a hand or any part of body in
fastener discharge area of tool.
Never point tool at anyone.
WARNING:
!
The warnings and precautions discussed
above cannot cover all possible
conditions and situations that may occur.
It must be understood by the user that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the user.
.
1-888-669-5672
MODEL:SFL618
UNPACKING
This tool has been shipped completely
assembled.
Carefully remove the tool and any accessories
from the box.
Inspect the tool carefully to make sure no
breakage or damage occurred during shipping.
Do not discard the packing material until you
have carefully inspected and satisfactorily
operated the tool.
If any parts are damaged or missing, please
call 1-888-669-5672.
WARNING:
!
If any parts are missing do not operate
this tool until the missing parts are
replaced. Failure to do so could result in
possible serious personal injury.
If an
WARNING:
!
Do not attempt to modify this tool or
create accessories not recommended for
use with this tool. Any such alteration or
modification is misuse and could result
in hazardous condition leading to
possible serious personal injury.
FEATURES
SPECIFICATIONS
Operation pressure:
Nails capacity:
Tool weight:
Air inlet:
Fasteners:
Ga.16
Compatible with Generic Brands of 1/2" Staples,
T-Cleats, & L-Cleats.
FEATURES
REVOLUTIONARY 3 IN 1 DESIGN
For use with Staples, T-Cleats and L-Cleats.
ERGONOMICALLY DESIGNED HANDLE
For ease of operation and reduced fatigue.
DURABLE CONSTRUCTION
Lightweight and durably constructed of high-
strength aluminum and heat treated steel parts.
MALLET INCLUDED
OPERATION
The tool is shipped with the Arm part detached from
the Main body part.
70-110psi
L: 100pcs
T: 100pcs
U : 120pcs
11 lbs
1/4"NPT
. .
HTTP://WWW NUMAXTOOLS COM 1-888-669-5672
Ga.16
05