Setting The Air Pressure; Operating The Tool - Numax SFL618 Manual Del Usuario

MODEL:SFL618
Make sure all items listed above in the picture are
included in the package, if not, call 1-888-669-5672.
Follow these instructions to prepare the tool for
using.
1. Set the Arm against the Handle and slide the
Brackets through the Arm holes slots and holes.
Thread Washers and Nuts over ends of brackets.
2. Wrench-tighten the Nuts until Brackets are
secured and the Arm is locked against Handle.
06
.
HTTP://WWW NUMAXTOOLS COM
If any parts are missing, do not operate
this tool until the missing parts are
replaced. Before using this tool, make
sure the arm part and the main body part
are screwed together tightly. Failure to
do so could result in possible serious
personal injury.
LOADING CLEAT NAILS
⒈ Pull the Pusher(A) back to the end of magazine.
Lock pusher in the place by using the Lock
button(C). Then pull the Magazine side shelter(B)
back.
Place full clip of desired Fasteners into magazine
⒉
from the side. Up to 100 cleat nails can be loaded
into magazine. Be noted that, when loading the L
cleat nails, the side with the L head should be in
the left of the Magazine side shelter(B). Press the
Lock button(C), then the Pusher(A) set back to
make the Magazine side shelter(B) down back.
LOADING STAPLES
⒈ Pull the Pusher(A) back to the end of magazine.
Lock pusher in the place by using Lock button(C).
Then pull the Magazine side shelter(B) back.
⒉
Place a full clip of 1/2" Crown Staples in the
magazine from the top. Up to 120 pcs can be
loaded into the tool.
⒊ Press the Lock button(C), then the Pusher(A) sets
back to make the Magazine side shelter(B) down
back.
WARNING:
!
The tool may fire when it first connected
to the air resource. Always connect the
tool to the air resource before loading
fasteners to prevent injury from
unintended cycling. Always make sure
the tool's magazine is empty at the
beginning of each work session, before
connecting to an air source.
Lock button(C)
Magazine side
shelter (B)
Pusher (A)
.
1-888-669-5672
MODEL:SFL618
CHANGE THE FOOT PLATE
The tool is equipped with a factory pre-installed
25/32" (3/4") foot plate(D). And an additional
uninstalled 1/2" foot plate.
To change the plate:
Disconnect the tool from the air source.
⒈
Empty the magazine completely.
⒉
⒊ Fire the tool into a piece of scrap wood to ensure
there is no compressed air or fasteners left in the
tool.
Set the tool on its side to expose the three
⒋
screws(E).
⒌ Remove the three screws(E), then, remove the
foot plate.
⒍ Align the three screw holes in the replacement
foot plate with the three threaded mounting
holes.
Using the three screws you removed just now,
⒎
secure the replacement foot plate to the tool.
⒏
Ensure the correct Foot Plate is installed by
firing into a scrap piece of flooring and checking
for proper fastener placement.
WARNING:
!
Disconnect the tool from the air source
whenever changing the foot plate.
Make sure there is no fastener in the
magazine before changing the foot plate.
Foot plate (D)
Screws(E)

SETTING THE AIR PRESSURE

The amount of air pressure required depends on
the size of the fasteners and the workpiece material.
Begin testing the depth of drive by driving a test nail
into the same type of workpiece material used for
the actual job.
Drive a test fastener with the air pressure set at 90-
95psi. Raise or lower the air pressure to find the
lowest setting that will perform the job with
.
HTTP://WWW NUMAXTOOLS COM
consistent results.
It may be possible to achieve the desired depth with
air pressure adjustments alone.

OPERATING THE TOOL

⒈ Attach the tool to the air source. Start your
compressor and check the pressure, making sure
it is set between 70-110psi. Do not exceed the
maximum 120psi.
Hold the Hand grip(F) securely and Press the
⒉
Foot plate(D) to the work surface. Make sure the
plate is over the Fastener target position.
⒊ Press down hard so that the foot plate is firmly
contacting the work surface. Then, using the
mallet packed with the tool, strike the hammer
cap(G) firmly to drive the fastener into work
surface. Lift the tool off the work surface. Repeat
this process until the job is completed.
⒋ When finished, make sure to store the tool in a
clean, dry, safe location out of reach of children
and other unauthorized People.
WARNING:
!
Extreme caution must be used whenever
this tool is connected to an air resource.
If the tool is dropped, or if the Hammer
cap(F) is accidentally struck, then the tool
will fire a fastener, potentially causing
SERIOUS PERSONAL INJURY.
WARNING:
!
Keep your feet off the tool.
WARNING:
!
Before using the tool on a floor, test the
tool on a scrap piece of wood. Adjust the
driving depth by providing more or less
air pressure. Never exceed 120PSI.
.
1-888-669-5672
07