Recommended Hookup - Numax SFL618 Manual Del Usuario

MODEL:SFL618
CLEARING JAMS
Occasionally, fasteners may become jammed in the
firing mechanism of the tool, making the tool
inoperable. To remove a jammed fastener, follow
the steps below:
⒈ Disconnect the tool from air source.
⒉ Empty the magazine. Make sure all fasteners are
removed.
⒊ Try to fire the tool into a piece of scrap wood or
flooring to make sure that it's incapable of firing
any fasteners.
⒋ Lean the tool back. With the Drive guide(H) facing
away from you, remove the three Bolts(I).
Then remove the Drive guide(H) to expose the
jammed fastener.
Removed jammed fastener, using pliers or a
⒌
Screwdriver if required.
⒍ Replace the Drive guide(H) and Bolts(I).
⒎ Reload the tool with fasteners. then, reconnect
the air resource to the tool.
Press the Drive guide(H) against a piece of wood,
⒏
and test fire the fasteners several times to check
for proper operation. If the tool is properly firing,
you may continue using the tool. If the tool fails to
perform properly, immediately discontinue use
and have the tool repaired by a qualified service
technician.
When finished working, disconnect the air source.
⒐ Remove fasteners. Discharge any trapped air.
Then store the tool in a clean, dry, safe location
out of reach of children.
WARNING:
!
Make sure there is no fastener in
magazine before clearing a jam.
WARNING:
!
Disconnect the tool from the air source
whenever clearing a jam. After
disconnecting the tool from the air
compressor, there should still be enough
air pressure to fire the tool. After the air
hose is disconnected, always fire the tool
into scrap wood repeatedly to make sure
all of the compressed air is expended.
08
.
HTTP://WWW NUMAXTOOLS COM
Drive
guide(H)
MAINTENANCE
WARNING:
!
Any time inspection, maintenance, and
cleaning are done:
◆Disconnect the tool from the air
◆ Empty the magazine completely.
ANTI-DUST CAP
Each tool is packed with an anti-dust cap on the air
connector, check it after unpacking. Keep the anti-
dust cap to cover the air connector when the tool is
not in use to prevent the dust.
LUBRICATION
Frequent, but not excessive, lubrication is required
the
for best performance. Oil for the tool added through
the air line connection add will lubricate the internal
parts. Do not detergent oil or additives as these
lubricants will cause accelerated wear to the seals
and bumpers in the tool, resulting in poor tool
performance and frequent tool maintenance.
CAUTION:
Lubricate tool only with specified
lubricants.
CLEANING
Avoid using solvents when cleaning plastic parts.
Most plastics are susceptible to damage from
various types of commercial solvents and maybe
damaged by their use. Use clean cloths to remove
dirt, dust, oil, grease, etc.
.
1-888-669-5672
MODEL:SFL618
WARNING:
!
Do not at any time let brake fluids,
gasoline, petroleum-based products,
penetration oils, ect. come in contact
with plastic parts. Chemicals can damage,
weaken or destroy plastic which may
result in serious personal injury.
COLD WEATHER OPERATION
Bolts(I)
For cold weather operation, near and below freezing,
the moisture in the air line may freeze and prevent
tool operation. We recommend the use of air tool
lubricant or permanent anti-freeze (ethylene glycol)
as a cold weather lubricant.
source.
CAUTION:
Do not store tools in a cold weather
environment to prevent frost or ice
formation on the tools' operating valves
and mechanisms that could cause tool
failure.

RECOMMENDED HOOKUP

1. The air compressor must be able to maintain a
minimum of 70 psi when the tool is being used.
An inadequate air supply can cause a loss of
power and inconsistent driving.
2. An oiler can be used to provide oil circulation
through the tool. A filter can be used to remove
liquid and solid impurities which can rust or gum
up internal parts of the tool.
3. Always use air supply hoses with a minimum
working pressure rating equal to or greater than
the pressure from the power source if a regulator
fails, or 150 psi, whichever is greater. Use 3/8
air hose for runs up to 50 . Use
50 run or longer. For better performance, install '
a 3/8 quick plug (1/4" NPT thread) with an "
inside diameter of 0.315 (8mm) on the tool and
3/8 quick coupler on the air hose. "
4. Use a pressure regulator on the compressor,
with an operating pressure of 0-125 psi. A
pressure regulator is required to control the
operating pressure of the tool between 70 and
110 psi.
CAUTION:
The air compressor must be able to
maintain a minimum of 70psi when the
tool is being used. An inadequate air
supply can cause a loss of power and
inconsistent driving.
WARNING:
!
Do not connect with an air compressor
which can potentially exceed 200psi. As
tool may burst, possibly causing injury.
. .
HTTP://WWW NUMAXTOOLS COM 1-888-669-5672
"
' ½ " air hoses for
"
09