Important Notices; General Safety Precautions - Casals SP1200 Instrucciones Del Producto Original

English
SANDER POLISHER
SP1200
IMPORTANT:
Thank you for purchasing a Casals Circular saw
(hereinafter referred to as the "Circular saw").
This manual will assist you in operating and main-
taining your Circular saw. This manual is the latest
version.
With the continuous improvement and upgrading of
this product, the manufacturer reserves the right to
modify this manual without notice. The manufactur-
er shall assume no liability for incorrect information
contained in this manual.
This manual is an integral part of the Circular saw.
When the Circular saw is transferred to others, this
manual should be handed over to the new owner.
Some important information in this manual will be
indicated in the following way (please see below).
The users should pay special attention to these
instructions.
The range of CASALS POWER TOOLS is safe
and reliable, but incorrect use of these prod-
ucts may cause personal injury and or damage
to your machine. Please read this manual
thoroughly before operation as this product is
required to operate strictly in accordance with
this manual.

IMPORTANT NOTICES:

WARNING: When using the Circular saw, basic
safety precautions including the following safety in-
structions should always be followed to reduce the
risk of fire, electric shock and personal injury. Read
all these instructions before operating this product
and retain these instructions for future reference.

1. GENERAL SAFETY PRECAUTIONS:

1.1. This power tool is not intended for use by
persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experi-
ence and knowledge, unless they have been given
supervision or instruction concerning use of the
power tool by a person responsible for their safety.
1.2. The power tool may only be operated observ-
ing the regulations of the operation documentation
and under permanent supervision.
1.3. Do not operate this product in an explosive
atmosphere, such as in the presence of flammable
liquids, gases or dust.
1.4. Keep children and bystanders away while
operating the power tool. Distractions can cause
you to lose control.
1.5. The power tool's plug must match the outlet.
Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock
1.6. Avoid body contact with earthed or grounded
surfaces such as tubes, radiators and refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded. (If applicable)
1.7. Do not expose the power tool to rain or wet
conditions. Water entering the power tool will
increase the risk of electric shock.
1.8. Do modify or change the cord. Never use the
cord for carrying, pulling or unplugging the power
tool. Keep the cord away from heat, oil and sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
1.9. When operating this power tool outdoors, use
an extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
1.10. Stay alert. Watch what you are doing and use
common sense when operating the power tool.
1.11. Do not operate the power tool when you are
tired or under the influence of drugs, alcohol or
medication.
1.12. Use safety equipment. Always wear eye
protection. Safety equipment such as dust mask,
non-skid safety shoes, hardhat, or hearing protec-
tion used for appropriate conditions will reduce
personal injuries.
1.13. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
1.14. Do not over reach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
1.15. Dress properly. Do not wear loose clothing or
jewellery; Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
1.16. Do not force the power tool.
1.17. Do not use the power tool if the switch does
not turn it on and off. If the power tool cannot be
controlled by the ON/OFF switch, disconnect from
power source and send for service.
1.18. Disconnect the plug from the power source
before making any adjustments, changing acces-
ORIGINAL instructions