Air Source; Recommended Hookup; Operating Instructions; Lubrication - Campbell Hausfeld AT0510 Manual De Operación

Operating Instructions

Important Safety Instructions
(Continued)
b. When servicing a tool, use only
identical replacement parts. Use
only authorized parts.
c. Use only the lubricants supplied
with the tool or specified by the
manufacturer.
Do not make any
modifi cations to
the tool without fi rst obtaining written
approval from Campbell Hausfeld. Do
not use the tool if any shields or guards
are removed or altered. Do not use the
tool as a hammer. Personal injury or
tool damage may occur.

AIR SOURCE

a. Never connect to an air source that
is capable of exceeding 200 PSI.
Over pressurizing the tool is able
to result in bursting, abnormal
operation, breakage of the tool or
serious injury to persons. Use only
clean, dry, regulated compressed air
at the rated pressure or within the
rated pressure range as marked on
the tool. Always verify prior to using
the tool that the air source has been
adjusted to the rated air pressure or
within the rated air-pressure range.
b. Never use oxygen, carbon dioxide,
combustible gases or any bottled
gas as an air source for
the tool. Such gases are
capable of explosion and
serious injury to persons.
Do not
use any
type of reactive gases, including,
but not limited to, oxygen and
combustible gases, as a power
source. Use fi ltered, lubricated,
regulated compressed air only.
Use of a reactive gas instead of

Recommended Hookup

www.campbellhausfeld.com
compressed air may cause the tool
to explode which will cause death
or serious personal injury.
a pressure-regulated
compressed air source
to limit the air pressure
supplied to the tool. The regulated
pressure must not exceed 90 PSI.
If the regulator fails, the pressure
delivered to the tool must not
exceed 200 PSI. The tool could
explode which will cause death or
serious personal injury.
SAVE THESE INSTRUCTIONS
OPERATING INSTRUCTIONS

LUBRICATION

Proper lubrication is the owner's
responsibility. Failure to lubricate the air
tool properly will dramatically shorten
the life of the tool and will void the
warranty.
lubrication before the initial
use and before and after each
additional use.
Air tools require lubrication throughout
the life of the tool. Air tool oil is
recommended because this oil cleans,
lubricates and inhibits rust all in one
step. Use Campbell Hausfeld air tool oil
ST127001AV or equivalent ISO grade 32
O
CO
2
oil.
lubricated, oil will discharge
through the exhaust port during
the fi rst few seconds of operation.
Thus, the exhaust port must be
covered with a towel before
applying air pressure. Failure to
cover the exhaust port can result in
serious injury.
Quick
Coupler
Quick Plug
Air Hose
Use only
90 PSI
DO NOT DISCARD
This air tool
requires
After an air tool
has been
Quick
Quick Plug Coupler
(Optional)
(Optional)
Lubricator
4
1. Disconnect tool from air supply.
2. Turn tool upside down.
3. While pressing trigger, apply 5 - 10
drops of oil in the air inlet.
4. Connect the air tool to the air supply
and cover the exhaust port with a
towel. Run the air tool for 7 to 10
seconds. Oil will discharge from the
exhaust port when air pressure is
applied.
RECOMMENDED HOOKUP
The illustration below shows the
recommended hookup for the tool.
1. The air compressor
must be able to
maintain a minimum
of 60 PSI when the
tool is being used.
An inadequate air supply can cause
a loss of power and inconsistent
driving.
2. An oiler can be
used to provide oil
circulation through
the tool. A filter can
be used to remove
liquid and solid impurities which can
rust or "gum up" internal parts of
the tool.
3. Always use air supply hoses with
a minimum working pressure
rating equal to or greater than the
pressure from the power source if a
regulator fails, or 200 PSI, whichever
is greater. Use 1/4 inch air hose for
200 PSI or greater
Regulator
Filter
60 PSI
Min.
90 PSI
Max.
3/8 inch I.D.