Warranty Information - Bullard 41 Serie Manual De Instrucciones

Bullard 41EAK European Adapter Kit
The Bullard 41eAK european Adapter Kit is supplied to accommodate the
threaded coupling and fitting requirements and standards of europe.
This Kit contains:
1 ea. 1" (25 mm) X 3/4" (19 mm) pipe reducing bushing
2 ea. 1/4" (6 mm) MpT British thread adapter
1 ea. 3/8" (7 mm) X 1/4" (6 mm) reducing bushing
installing Adapters:
1. Before using 41p2e filter:
• Locate the 1" (25 mm) X 3/4" (19 mm) pipe Reducing Bushing in the
41eAK Kit bag.
• Apply thread sealant to the 1" (25 mm) X 3/4" (19 mm) pipe Reducing
Bushing.
• Install the 1" (25 mm) X 3/4" (19 mm) pipe Reducing Bushing into the
air inlet on side of filter (refer to Figure 4 below).
• Tighten with a wrench until wrench tight.
2. If only one air outlet is required:
• Locate the 1/4" (6 mm) MpT British Thread adapter in the 41eAK Kit
bag.
• Remove the existing pipe-to-hose adapter from the SIDe of the top
mounted regulator, using a wrench.
• Apply thread sealant to the 1/4" (6 mm) MpT British Thread adapter.
Figure 4

Warranty information

Bullard warrants to the original purchaser that the Airline Filter is free of
defects in materials and workmanship under normal use and service for a
period of one (1) year from the date of manufacture. Under this warranty,
Bullard's obligation is limited to repairing or replacing, at its option, articles
that are returned within the warranty period and that, after examination,
are shown to Bullard's satisfaction to be defective, subject to the following
limitations:
a) Airline Filter must be returned to Bullard with shipping charges prepaid.
b) Airline Filter must not be altered from its original factory configuration.
c) Airline Filter must not have been misused, abused or damaged in
storage or transit.
In no event shall Bullard be responsible for damages resulting from loss of
use or other indirect, incidental, consequential or special costs, expenses
or damages incurred by the purchaser, notwithstanding that Bullard has
been advised of the possibility of such damages.
• Install the 1/4" (6 mm) MpT British Thread adapter into the open port
(refer to Figure 5 below).
• Tighten with a wrench until wrench tight.
3. If a second air outlet is required.
• Locate the 3/8" (7 mm) X 1/4" (6 mm) MpT bushing and the 1/4" (6
mm) MpT British Thread adapter in the 41eAK Kit bag.
• Remove the existing pipe plug from the TOp of the top mounted
regulator, using a wrench.
• Apply thread sealant to the 3/8" (7 mm) X 1/4" (6 mm) MpT bushing.
• Install the 3/8" (7 mm) X 1/4" (6 mm) MpT bushing into the open port
(refer to Figure 6 below).
• Tighten with a wrench until wrench tight.
• Apply thread sealant to the 1/4" (6 mm) MpT British thread adapter.
• Install the 1/4" (6 mm) MpT British Thread adapter into the open end
of the 3/8" (7 mm) X 1/4" (6 mm) bushing that was installed in the step
above (refer to Figure 7 below).
• Tighten with a wrench until wrench tight.
Figure 5
ANY IMpLIeD WARRANTIeS, INCLUDING WARRANTIeS OF
MeRCHANTABILITY AND FITNeSS FOR pARTICULAR pURpOSe, ARe
LIMITeD TO ONe (1) YeAR FROM THe DATe THe AIRLINe FILTeR WAS
MANUFACTUReD.
The above limitations or exclusions may not apply in all states.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or allow limitations on how long an implied
warranty lasts. This warranty gives you specific legal rights, and you may
have other rights which vary between states.
RETURN AUTHORiZATiONS
Contact Customer Service to obtain written permission to return product.
Airline Filters cannot be returned without written permission. Material
returned for credit will be subject to factory inspection. Current products
or products under warranty will be subject to a restocking charge.
Returned articles should be sent to Bullard with shipping charges prepaid.
www.bullard.com
41 Series Airline Filters
User Manual
Figure 6
Figure 7
3