Environmental Conditions; Fitting; Tensioning The Springs; Operation - Solid Elements Solid Pro Iso Instrucciones Para El Montaje

ENGLISH
2 .3

Environmental conditions

ATTENTION
Damage due to temperature differences
Differences in the inside and outside temperatures may
cause deflection of the door elements (bi-metal effect).
This may result in damage when the door is operated.
f Comply with the operating conditions.
The door is intended for the following operating conditions:
Temperature:
• Exterior side
• Interior side
Relative humidity:
3

Fitting

WARNING
Danger of injury as the result of structural
modifications
Changing or removing functional parts may put important
safety components out of action. Uncontrolled door
travel could occur and persons or objects may be
trapped as a result.
f Do not alter or remove any functional parts.
f Do not attach any additional components. The
torsion springs are precisely matched to the door leaf
weight. Additional components may overload the
springs.
f If equipping the door with an operator, pay attention
to the instructions provided by the manufacturers of
the door and operator. Only use the original
connections of the door manufacturer!
Before fitting the door, the door opening and the building
floor must be completely finished.
Observe the following during fitting:
• Establish a secure connection with the building
structure.
• Check that the fixing materials supplied are suitable for
the given structural conditions.
• Do not fasten the door system to supporting structural
members unless you have obtained the prior approval
of the structural engineer.
• Ensure adequate water run-off in the area of the
bottom seal and the frame parts, otherwise there is a
danger of corrosion. (see Technical Manual)
• Ensure sufficient drying and ventilation in the building,
otherwise there is danger of corrosion.
• The door must be effectively protected before carrying
out plastering and paintwork, as splashes of mortar,
cement, plaster, paint etc. can damage the door
surface.
• Protect the door from caustic, aggressive substances,
e.g. nitrous reactions from stones or mortar, acids,
alkali solutions, de-icing salt, aggressive paints or
sealants. Failure to do so, could lead to corrosion.
• Clean the door surfaces with clear water, a soft sponge
and a neutral, non-abrasive cleaning agent.
f To ensure simple and secure fitting, please follow
the work steps listed in the illustrated section .
12
3 .1
Danger of injury due to high spring tension
Springs are under high tension and may discharge high
forces if they are not secured during tensioning.
f Fix the door leaf to prevent uncontrolled movement
When the springs are tensioned correctly, the moving door
leaf has a slight tendency to pull upwards.
f Each time the door is serviced, the tension of the
– 40 °C to + 60 °C
– 20 °C to + 60 °C
20 % to 90 %
f Before putting the door into operation for the first
4
4 .1
Danger of injury during door travel
The sectional door opens to the top vertically; persons or
objects may be trapped.
f When operating the door, always make sure that
f Always keep the opening area of the door clear.
f Do not operate the door in strong winds.
The door must only be operated by suitably instructed
persons. If the sectional door is competently fitted and
inspected, it can be easily moved and operated.
4 .1 .1
The automation of a sectional door requires that special
safety regulations be observed. Consult your supplier.
5
Scratches on the panes due to improper cleaning
Rubbing the panes causes scratches.
f Dirt and dust particles must first be thoroughly rinsed
Clear water is sufficient for cleaning and care . Use
warm water together with a neutral, non-abrasive cleaning
agent (household detergent, pH value 7) if more heavily
soiled. To preserve the surface characteristics, regular
cleaning must be carried out at least every 3 months
(outside of door, seals). The slide area behind the side
seals must be kept permanently clean and able to slide.

Tensioning the springs

WARNING
before adjusting the tension springs.
springs should be checked and, if necessary,
subsequently re-adjusted.
time, inspect the door according to the chapter
Inspection and Maintenance!

Operation

Operating the door

WARNING
there are no objects or persons, especially children,
within the door's range of movement!
Power-driven doors

Cleaning and Care

ATTENTION
off with water. If necessary, only wash with water, a
pH-neutral household detergent and a soft, clean
cloth.
4 013 867 RE / 07.2019