Parts List; Before Lighting - Ooni Koda Manual Del Usuario

• The parts which have been sealed by the manufacturer should not be adjusted by the user
• When the appliance is using LPG A LPG cylinder should be used
• The LPG cylinder size: max diameter-350mm, max height-400mm.
• The appliance is to be installed with sufficient ventilation to prevent the occurrence of unacceptable concentrations of substances
harmful to health in the room in which the appliance is installed
• The minimum distances between the appliance and adjacent walls is 0.5m
• The hose for the appliance should not exceed 1.5m
• The appliance should be installed in a suitably ventilated room. Permanent supply of fresh air is ensured and there is no accumulation
of unburned gases
• The gas supply tubing or hose shall comply with the national requirements in force and shall be periodically examined and replaced as
necessary.
• The hose should comply with the standard EN16436. The regulator should comply with the standard EN16129.
• The hose and regulator assembly may not be provided with the appliance in some regions.
• Check and suitably clean the inside of the oven before it is lit in order to avoid the emission of fire from the oils that have accumulated
during previous cooking.
• The burner outlets should be checked for obstruction during previous cooking.
• The burner outlets should be checked for obstruction and cleaned regularly with a soft wire brush.
• It is necessary to avoid obstruction and to allow for a good combustion

BEFORE LIGHTING

Inspect the gas supply hose prior to turning on the gas. If there is evidence of cut, wear or abrasion, it must be replaced prior to use.
Screw the regulator onto the gas cylinder. Leak check the hose and regulator connections with a soap and water solution before lighting
the appliance.
LP GAS CYLINDER WARNING
1. Do not store spare liquid propane gas cylinder under or near this appliance.
2. Never fill the cylinder beyond 80 percent capacity.
3. Liquid propane cylinder must be fitted with an OVERFILL PROTECTION DEVICE (OPD).
4. If the information above is not followed exactly, a fire resulting in death or serious injury may occur.
SAFETY PRACTICES TO AVOID INJURY
When properly cared for, your oven will provide safe, reliable service for many years. However, extreme care must be used as the oven
produces intense heat that can increase the risk of accidents.
When using this oven basic practices must be followed, including but not limited to following:
• Do not repair or replace any part of the oven unless specifically recommended in this manual. All other service should be referred to a
qualified technician.
• Children should not be left alone or unattended in an area where the oven is being used. Do not allow children to sit, stand or play
around the oven at any time.
• Never let clothing or other flammables come in contact with or too close to any burner or hot surface until it has cooled. The fabric
could ignite, causing serious personal injury.
• For personal safety, wear proper apparel. Loose fittings garments or sleeves should never be worn while using the oven. Some
synthetic fabrics are highly flammable and should not be worn while cooking.
• Do not heat unopened food containers as a buildup of pressure may cause the containers to burst. When lighting the burner, always
pay close attention to what you are doing.
• When using the oven, do not touch the outer shell, stone baking board or immediate surroundings as these areas become extremely
hot and could cause burns.
• Do not use the oven to cook extremely fatty meats or other products which increase flare-up.
• Keep the area surroundings the oven free from combustible material including fluids, trash and vapours such as gasoline or charcoal
lighter fluid.
• Do not obstruct the flow of combustion and ventilation air.
• Never use the oven in extremely windy conditions.
• The temperature under the oven is high. Do not place the oven on a table with flammable table cloths, plastic or any other
inflammable materials.
2

PARTS LIST

1. Ooni Koda
2. Stone baking board
1.
ASSEMBLY
Before assembly, make sure all parts are present. If any part is missing or damaged, do not attempt to assemble the appliance. Contact
customer service for replacement parts.
1. Unfold legs
2. Insert the stone baking board
2.
3