Installation; Connecting Controllers And Sensors; Connecting Additional Sensors Or Other Devices; Which Sensors Can Be Connected To The T-Micro - TechGrow T-Micro Manual

1. Installation

1. Mount the CO sensor on the wall near the CO
2
source, with a minimum distance of 50 cm. It is
preferred not to place the sensor directly above the
CO source if it becomes very hot (CO
2
You should mount the sensor at a height of +/- 1
meter above the floor.
2. Do not place the sensor in the direct airflow of fans
as this may affect the measurements.
3. Connect the sensor(s) to the bottom of the T-Micro
with the supplied (UTP) cable(s).
4. Plug the CO source to the T-Micro.
2
5. Plug the plug of the T-Micro into a 230V socket.
6. Ready!

2. Connecting controllers and sensors

Most of TechGrow's controllers and sensors can be
interconnected to ensure an optimal user experience.
Interconnecting the controllers enables to control the
total climate with only one S-4 Sensor. Since each
device has 2 UTP connectors, it is not only possible to
interconnect the devices, but also to connect a
Datalogger DL-1, for example.
Make sure that all controllers are equipped with mains
voltage, and check if the controllers are switched off
before you connect sensor(s) to prevent any
malfunctions. The sensor can be connected to any UTP
connector.
The regular TechGrow sensors are comparable to the
sensors from the TechGrow Pro Series and can
therefore also be used for controllers from the Pro
Series.
3. Connecting additional sensors or
other devices
The T-Micro can measure the values of connected CO
RH and temperature sensors, and transmit the data to
the connected controller, provided it is linked to an S-4
Sensor. However, the T-Micro only regulates
the CO .
2
If you want to connect another sensor to the T-Micro,
first switch off the controller, wait a few seconds, and
then reconnect the controller to the power outlet.
4. Which sensors can be connected to
the T-Micro?
The minimum sensor required is a S-2 Sensor
____________________________________________________________________________________________________________________________
TechGrow | Innovative Growing Solutions
(or our future Budget CO
ATTENTION: NEVER connect two of the same type
2
of sensors to your controller! For example: a S-4
Sensor and a Temp/RH Sensor must not be
connected at the same time.
generator).
2
5. Automatic functions of the T-
Micro
1. If no CO
will be shown on the display as NO*SENSOR.
2. When it is dark, no CO
that the sensor can detect the light source directly.
3. If the CO
released.

6. Meaning LED

Between the two rotary knobs you see the "OK" LED,
which can indicate a number of things:
Green: there is sufficient CO
•
Red: the CO
•
Orange (flashing): something is wrong. The sensor
•
is missing or broken (NO*SENSOR), or calibration is
in progress.

7. Operation of the T-Micro

If the CO
(setpoint minus hysteresis), the CO
on.
Over time, the CO
setpoint, the source is switched off.
Example
The CO
The CO
,
2
The current CO
higher than the CO
off. The red light is off.
The CO
no action yet. Only when the value drops below the CO
setpoint minus the CO
= 630 ppm, the CO
comes on.
Now, the CO
ppm) is reached, the CO
and the LED lights green.
Sensor).
2
sensor is connected to the T-Micro, this
2
is released. So make sure
2
sensor is not detected, no CO
2
source is on.
2
value in the room drops under the set value
2
value rises and as it reaches the CO
2
setpoint is 670 ppm.
2
hysteresis is 40 ppm.
2
value in the room is 733 ppm: that is
2
setpoint, so the CO
2
level now slowly decreases to 670 ppm: there is
2
hysteresis, that is below 670 - 40
2
source switches on and the red light
2
level rises and when the setpoint (670
2
source is switched off again
2
is
2
in the room.
2
source is switched
2
2
source is turned
2
2
11