Sammic SAM-3001 Manual De Instrucciones página 6

Information on CE marking
Each machine is identified as follows:
- Name and address of the manufacturer: SAMMIC
S.L., Basarte 1, Azkoitia, Gipuzkoa (SPAIN).
- "CE" mark.
- The machine model is specified in the next
paragraph.
- The serial number is printed on the Guarantee
Card and in the Declaration of conformity.
MODELS
This manual describes the SAM-3001, SAS-
5001 and SAS-6001 Dryer Polisher installation,
operation and maintenance instructions. The
model reference and technical data appear on
the identification plate affixed to the machine.
European Directives and standards (version
400-230V III and 230V II):
- Machinery Directive 2006/42/EEC.
- Low Voltage Directive 2006/95/EEC.
- Electromagnetic Compatibility
2004/108/EEC.
- The 120V/60Hz/1~ models comply with the
UL-499 and CSA C22.2 standards.
- Study of machine's bacteriological function.
INSTALLATION
For optimum performance and long-lasting
preservation of your machine, carefully read
and follow the instructions given in this manual.
Location
Place the machine on a firm and perfectly
levelled ground.
This condition must be fulfilled for the machine
to operate within acceptable limits of vibration.
Level the machine using the adjustable feet (F).
It is recommended to leave a minimum
clearance of 40mm between the machine jacket
and the walls or other pieces of equipment
which may surround the dryer polisher.
Electric connection
Motor characteristics:
6 EN
A single-phase motor is supplied for operation on
230V or 120V.
A 2P (10A -16A) wall outlet, always within
reach, and a sealed plug are required.
A three-phase motor is supplied for operation on
230V or 400V (factory-set to 400V). To change
the voltage setting change the terminal box and
motor connection as shown on the wiring
diagram.
For three-phase motor powered machines, a
10A 4P wall outlet, always within reach, and a
sealed plug are required.
Before connecting the dryer polisher to the
mains, check that the motor is prepared to
operate on the actual mains voltage.
Power Cable Characteristics
The SAMMIC dryer polishers are delivered
complete with a thermoplastics-sheathed power
cable 2m in length. THIS APPLIANCE MUST
BE EARTHED. The machine earth wire is
Directive identified.
ELECTRONIC CONTROL FUNCTIONS
"general switch G"
General light switch, connects and disconnects
the machine power supply.
"power switch button I A"
Starts the machine if the cover is in the down
position.
With the machine stopped and the door open and
by keeping this key pressed down, the final grain
drying cycle is selected, and the light indicator
switches on (4).
With the machine switched on, by keeping this
key pressed down the UV-c lamp switches off
for 15 minutes. If you press the on switch button
again or stop the machine and switch it on, the
lamp comes on immediately.
"power switch button 0 B"
Stops the machine.
To switch off light indicator 3, change of polish
granules or change of lamp, with the machine
switched off and the door open keep the off
switch button pressed down.
"light indicator OK 1"
When the light is on, the granule has reached
the working temperature or the pre-selected
temperature (see operation).
"resistance light indicator 2"
If the light indicator is lit up the heater is
connected, and if it is not lit up the heater is
disconnected (see operation).
"change light indicator 3"
If the light indicator is on, the polish granules
need to be changed (see change of granules).
If the light indicator is blinking the UV-c lamp
needs to be changed (see change of UV-c
lamp).
"drying light indicator 4"
If the light indicator is off, the drying cycle has
been selected (see drying cycle).
If it is blinking, there is a machine failure (see
failures code).
OPERATION
Filling polish granules
Switch the machine on (see operation). Fill the
hopper with the amount of polish granules
supplied by SAMMIC through the central cutlery
inlet (C).
SAMMIC supplies a bag of polish granules with
each machine and these are the recommended
amounts of polish granules according to the
machine model:
SAM-3001 3 Kg. / 6.6 lbs. of polish granules.
SAS-5001 and SAS-6001: 5 Kg. / 11 lbs. of polish
granules.
If the motor direction of rotation is correct, the
product will be distributed evenly in the hopper
with an ascending movement. Once the
granules have been distributed evenly, switch
the machine off.
If this does not occur in three-phase models,
change the motor rotation
interchanging two of the phases in the wall socket.
Start up and stopping
Activate the general switch (G). With the cover
down and pressing the on switch button (A):
direction by