Sammic SAM-3001 Manual De Instrucciones página 8

MAINTENANCE
WARNING! Before cleaning or carrying out
maintenance of your dryer polisher, always
unplug it from the mains.
If any components need changing, contact a
SAMMIC authorised technical assistance
service. Due to the machine's vibration, any
incorrect action could damage it.
Change of polish granules each time the
change light indicator 3 lights up.
Change of UV-c lamp each time the change
light indicator 3 blinks.
Due to use and the presence of heat, the polish
granules emit dust. You must remove the polish
granules and clean the transparent cover, the
hopper and the accessible components once
every certain period. If the fan or the UV-c lamp
are covered in dust, they may not work properly.
Call the authorised technical assistance service
to clean and check them.
Before starting up the machine, check that it is
stands firmly on the ground.
If any component is replaced in the hopper, it
must be left in the same condition as before. If
the component, power cable, etc. assembly
instructions are not followed, the vibratory
action will damage the spare part in a short
space of time.
Note
If the power cable should get damaged, it would
be necessary to fit a new one; such a
replacement may be done only by a SAMMIC
authorised technical assistance service.
Should you observe any malfunction, contact a
SAMMIC authorised technical assistance
service as soon as possible.
Never power clean the outside of the machine.
Use a wet cloth and mild detergent for cleaning.
Never clean the polycarbonate hopper cover
with solvents, alcohol, window-cleaning fluids or
any abrasive materials, since they may be
harmful to the mechanical properties of the
cover.
8 EN
TROUBLESHOOTING
Cutlery discharge is not even
The cause might be:
1. Motor direction of rotation is incorrect. In the
case of three-phase motors, change the
polarity.
2. Cutlery jam. In this event: Stop the machine.
Lift the top cover. Check for jams in the
upward path. If any, remove the transparent
cover after loosening the fixing knobs. Clear
the obstruction. Be careful when introducing
your hands, as there may be sharp items.
Replace the cover and fix it with the rubber
washers and knobs. The transparent cover
should not be left loose, because this would
lead to an increase in noise and a possible
fatigue fracture of the cover.
3. The amount of polish granules is less than
specified.
4. The polish granules are very dry and have
reduced in volume. This effect is similar to
when the amount of polish granules is less
than necessary. Use very wet cutlery or add
a bit of water to increase the volume.
NOTE With excessive drying, the volume and
weight decrease. This must be supervised.
Granules or dust are coming out of the
outlet
· Too many polish granules.
· In the case of models SAM-3001 and SAM-
6001, there is a problem with the fan.
· The machine is dirty. Remove the polish
granules and clean the machine.
· The polish granules are very wet and there is
too much volume. Stop feeding cutlery and run
a drying cycle.
Note: With the presence of water, the polish
granules increase in volume and weight. This
must be supervised.
The dryer-polisher will not start
· The machine is plugged in and there is power
in the mains.
· The top cover is closed.
· The magnet on the top cover is not damaged.
· Top cover detection check: With the cover
closed, if you hold down "run" (A) for one
second and the machine does not start up but
the drying cycle indicator light 4 lights up, this
means that the electronic board does not
detect the door magnet or the detector is faulty.
· There may be problems with the keypad: If
you hear a beep when you press any button,
this means that the keypad is OK and that
the electronic board has a power supply and
is working. If there is no beep, the keypad
might be faulty or badly connected.
· There might be problems with the fuse:
Check the condition of the fuse in the control
box.
· There might be problems with the electronic
board: Look to see if the power reaches the
board. There is also an LED that lights up
when the cover is closed and turns off when
it is opened. Check the wiring and the board.
The dryer-polisher is vibrating excessively
· Check that the machine stands firmly on the
ground.
· The wheels and legs are in good condition.
· The heater light indicator 2 is lit up but the
ready machine light indicator is not switched
on. Check the polish granule temperature. If
you notice that it is not heating up, there is a
problem with the heater or the wiring.
The UV-C Germicide lamp does not light up
· The lamp has burnt out. Change the lamp.
· There is a problem in the lamp holder with the
heater or the starter unit. Change the lamp
holder.
· The electronic board does not activate this
outlet.
OTHER IMPORTANT INFORMATION
Sound level of the machine standing on a firm
ground and correctly braked is:
- When empty: less than 70 dB and the
background noise is 25 dB. Measurement is
made at a height of 1.6m and 1m away from the
source.