Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Manually Lighting
Your
Grill
By Paper
Match
To light your gas grill by match,
insert a match
into the
Lighting
Stick
and follow
steps 1 through
5 of the Grill
Lighting
instructions.
Then,
light the match
and place
Lighting
Stick through
the Cooking
Grid on the grill as
shown
below.
Turn
the nearest
Control
Knob
to the Hi
setting
to release
gas. The
Burner
should
light
immedi-
ately.
Match
_ighLighting
Stick
(Note:the
Lighting
Stick
is placed
in the
drawer.)
Never
lean
over
the
grill cooking
area
while
lighting
your
gas
grill.
Keep
your
face
and
body
a safe
distance
(at
least
18
inches)
from
the
front
of
grill when
lighting
your
grill
by
match.
Should a FLASHBACK fire occur in or around
the Burner Tubes, follow the instructions below.
Failure to comply with these instructions could
result in a fire or explosion that could cause
serious bodily injury, death, or property damage.
•
Shut off gas supply to the gas grill.
•
Turn the Control Knobs to OFF position.
•
Open the Grill Lid.
•
Put out any flame with a Class B fire
extinguisher.
•
Once the grill has cooled down, clean
the Burner Tubes and Burners according
to the cleaning
instructions
in this Use
and Care Guide.
If ignition does
not occur
in 5 seconds,
turn the Control
Knob(s)
and gas source
OFF
and conduct
a leak test
as explained
in the Use and Care section
of this guide.
If no leaks
are detected,
wait
5 minutes
for any gas
to clear
and repeat the lighting
procedure.
Troubleshooting
If the grill fails to light :
1. Turn
gas off at source
and turn Control
Knobs
to OFF.
Wait
at least 5 minutes
for gas to clear, then
retry.
2. If your
grill still fails
to light,
check
gas supply
and
connections.
3. Repeat
lighting
procedure.
If your
grill
still fails
to
operate,
turn the gas off at source,
turn
the Control
Knobs
to OFF,
then
check
the following:
[]
Misalignment
of Burner
Tubes
over Orifices
Correction:
Reposition
Burner
Tubes
over Orifices.
[]
Obstruction
in gas line
Correction:
Remove
fuel line from grill. Do not smoke!
Open
gas supply for one second
to clear any obstruction
from fuel line. Close off gas supply
at source
and recon-
nect fuel line to grill.
[]
Plugged
Orifice
Correction:
Remove
Burners
from grill by removing
the
screw
from
the rear of each
Burner
using
Phillips
Head
Screwdriver.
Carefully
lift each Burner
up and away
from
gas valve Orifice.
Remove
the Orifice
from
gas valve and
gently
clear any obstruction
with a fine wire. Then
reinstall
all Orifices,
Burners,
screws
and
cooking
components.
[]
If an obstruction
is suspected
in Gas Valves
or Manifold,
call the Grill Information
Center
1-888-317-7642
8am
to
8pm
CST, Monday
through
Friday.
FqObstruction
in Burner
Tubes
Correction:
Follow
the Burner
Tube cleaning
procedure
on page
27 of this Use and Care Guide.
[] Misalignment
of Ignitor
on Burner
Correction:
Check
for proper
position
of the Electrode
Tip as shown
in step
6 page
14. The
gap between
the
Spark
Electrode
Tip and
Spark
Receiver
should
be
approximately
3/16".
Adjust
if necessary.
With
the gas
supply
closed,
turn any Main
Burner
Control
Knob
to
J/, then
push
in and watch
for the presence
of a spark
at
the
Electrode.
[]
Disconnected
Electric
Wires
Correction:
Inspect the ignitor Junction
Box found
behind
the Control
Panel.
Connect
loose
Electric wires to
Junction
Box and try to light the grill.
[]
Weak AA battery
Correction:
Unscrew
the ignitor
Cap and replace
the
battery.
[]
If the
grill
still does
not
light
you
may
need
to
purge
air from
the
gas
line
or
reset
the
regulator
excess
gas
flow
device.
Note:
This
procedure
should
be
done
every
time
a new
LP
Gas
tank
is connected
to
your
grill.
To purge
air from
your
gas line and/or
reset
the
regulator
excess
gas
flow
device:
[]
Turn
Control
Knobs
to the
OFF
position.
[]
Turn
off the gas
at the
tank
valve.
[]
Disconnect
regulator
from
LP
Gas
tank.
[]
Let
unit
stand
5 minutes
to allow
air to purge.
[]
Reconnect
regulator
to the
LP
Gas
tank.
[]
Turn
tank
valve
on SLOWLY
1/4 of a turn.
[]
[]
Open
the
Grill
Lid.
Push
and
turn
the Left
Main
Burner
Control
Knob
to _,.
[]
Press
Electric ignitor for 3-4 seconds
to light
the
burners.
2O
Publicidad
Tabla de contenido
