LG 47LX9500 Manual Del Propietário página 189

Ocultar thumbs Ver también para 47LX9500:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Data5:
7
6
Main/Sub
Two/One Part
Channel
Picture
0 Main
0 Two
1 Sub
1 One
The table above lists the binary code which must be
converted to Hexadecimal before sending. For exam-
ple: The binary code to tune the sub source to an
NTSC cable channel is "1000 0001", which translates
to "81" in Hex.
* 7th bit : For which source do you want to change the
channel.
* 6th bit: Use a two part or one part channel. Most
cases just use 0 since it's ignored when using
NTSC.
* 5th bit: Use 0 with NTSC since it can only use the
physical channel number. Normally use 1 for ATSC
since most times it doesn't matter what the physical
number is.
* 4th bit: Set to 0.
* 3-0 bits: Choose signal type.
* Tune Command Examples:
1. Tune to the analog (NTSC) cable channel 35.
Data 00 = Physical of 35 = 23
Data 01 & 02 = No Major = 00 00
Data 03 & 04 = No Minor = 00 00
Data 05 = 0000 0001 in binary = 01
Total = ma 00 23 00 00 00 00 01
2. Tune to the digital local channel 30-3.
Data 00 = Don't know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Minor is 3 = 00 03
Data 05 = 0010 0010 in binary = 22
Total = ma 00 00 00 1E 00 03 22
Acknowledgement[a][ ][Set ID][ ][OK][Data00]
[Data01] [Data02][Data03][Data04][x][a][ ][Set ID][ ]
[NG][Data00][x]
5
4
Using Physical
Reserved
Channel
0 Use
x
1 No Use
x
x
x
x
x
x
x
x
x
3
2
1
0
0
0
0
0
NTSC Air
0
0
0
1
NTSC Cable
0
0
1
0
ATSC Air
0
0
1
1
ATSC Cable_std
0
1
0
0
ATSC Cable_hrc
0
1
0
1
ATSC Cable_irc
0
1
1
0
ATSC cable_auto
0
1
1
1
Reserved
x
x
x
x
...
1
1
1
1
Reserved
21. Channel Add/Del (Command: m b)
To add and delete the channels.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00: Channel Delete Data 01: Channel Add
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
22. Key (Command: m c)
To send IR remote control code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
See page 183.
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
When TV is in the standby mode, TV will turn on by
POWER button of remote control only.
23. Backlight (Command: m g)
To adjust screen backlight.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min:00 ~ Max:64 (*transmit by Hexadecimal code)
*Refer to 'Real data mapping' .
Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]
Step
189

Publicidad

Capítulos

Tabla de contenido
loading

Este manual también es adecuado para:

55lx9500

Tabla de contenido