Multiplex A-SENSOR 150 A Manual De Instrucciones página 8

11. Additional sensors can be connected to the socket marked
"MSB" on the current sensor. If necessary it is possible to con-
nect two sensors to the sensor bus using a Y-lead (# 8 5030).
8. S
ETTING UP A REMOTE
If necessary, the current sensor's RESET button can also be
operated "remotely". This is the procedure:
1. Solder a two-core extension lead to the solder pads on the
current sensor's circuit board marked by arrows in
2. Use a square-section file to create an opening in the top of the
current sensor case close to the cable exit, so that the
extension lead is not crushed when the case is re-assembled
(see arrow in Fig. 8).
3. Solder a push-button to the other end of the extension lead,
and insulate each joint with a heat-shrink sleeve.
9. C
ONFIGURING THE SENSOR USING THE
MULTI
MATE OR
PC
PROGRAM
The Current Sensor 150 A can be connected on its own to a PC
or notebook using a MULTImate (# 8 2094) or the MULTIPLEX
Launcher PC program and the PC connecting lead (# 8 5149), for
the purpose of configuring the unit.
The MULTIPLEX Launcher PC program can be downloaded at
no charge from the MULTIPLEX website (www.multiplex-rc.de).
This program, or the MULTImate (V1.52 or later) opens up the
following options:
The following points can be activated and adjusted using
the MULTImate or MULTIPLEX Launcher
Address at the transmitter or Telemetry-Display
Address
at which the actual current flowing is displayed
Upper current value, above which an alarm is
Upper alarm
triggered
Lower current value, below which an alarm is
Lower alarm
triggered
Supplementary output of minimum, average or
Option
maximum current
Option address Address at which the option value is displayed
Period which elapses before the measurement
Delay time
commences (after switching ON)
Address at which the discharged energy or
Address
residual charge is displayed
Batt. capacity Nominal capacity of the connected battery
Display in Display in charge (mAh) or as percentage (%)
Charge value below which an alarm is
Alarm
triggered
! Note:
We advise you to keep your MULTImate or MULTIPLEX Laun-
cher current by updating it at regular intervals.
10. C
ONFIGURING WITH THE
This chapter lists the configuration options when using the MUL-
TIPLEX MULTImate, as displayed in both the English and Ger-
man menu systems.
11 MPX Sensors / MPX Sensoren
11-3 Settings / Einstellung
I / I (= current)
Address / Adresse (= address)
off / aus (= off), or an address
in the range 0 to 15
Alarm low / Alarm unten (= lower alarm)
off / aus (= off), or a current
in the range – 150.0 A to 150.0 A
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten (Gölshausen) • www.multiplex-rc.de
Operating Instructions for the
Current Sensor for M-LINK receivers (150 A)
RESET
BUTTON
MULTIPLEX L
AUNCHER
MULTI
MATE
Alarm high / Alarm oben (= upper alarm)
off / aus (= off), or a current
in the range – 150.0 A to 150.0 A
Option / Option (= option)
Max value, Min value, Average /
Maximalwert, Minimalwert, Mittelwert
(= maximum value, minimum value or average),
in each case in A
Option addr. / Option Adr. (= option address)
Fig. 7.
off / aus (= off), or an address
in the range 0 to 15
Mincurr./avg / Minstrom/MiWe
(= minimum value for average value calculation)
menu point not available for the current sensor 150 A
(= not available / nicht verfügbar)
Startup delay / Wartezeit
(= period after switching ON after which the
measurement commences)
Period
in the range 0 to 3 seconds
Q / Q (= charge)
Address / Adresse (= address)
off / aus (= off), or an address
in the range 0 to 15
Indication in / Anzeige in
(= display in charge quantity or %)
select facility: Charge mAh / Ladung (mAh) or:
Percent (%) / Prozent (%)
Batt.capacity / Akkukapazität
(= nominal capacity of the connected battery
Capacity value
in the range 0 mAh to 16000 mAh
Alarm / Alarm
(= what is the residual charge value at which the alarm is to be
triggered?)
off / aus (= off), or a value
in the range 0 mAh to 16000 mAh or
in the range 0% to 100%
11-3 Send data / Daten send. (= send data)
long press on the adjuster wheel sends the data
11-2 Clear opt. / Opt.löschen (= reset the option values)
long press on the adjuster wheel erases the option values
11. C
ONFIGURING WITH THE
L
AUNCHER
This chapter lists the configuration options using the MULTIPLEX
Launcher PC program, as displayed in both the English and Ger-
man menu systems.
Current I / Strom I (= current)
Address / Adresse (= address)
off / aus (= off), or an address
in the range 0 to 15
Alarm high / Alarm oben (= upper alarm)
off / aus (= off), or a current value
in the range – 150.0 A to 150.0 A
Alarm low / Alarm unten (= lower alarm)
off / aus (= off), or a current value
in the range – 150.0 A to 150.0 A
Address / Adresse (= option address)
off / aus (= off), or an address
in the range 0 to 15
MULTIPLEX
PC
PROGRAM
Page 3/4