C-LOGIC 645-MD Manual De Instrucciones página 2

INSTRUCTIONS MANUAL
Motion detector flush-mounted installation
C-LOGIC 645-MD
SKU: CLOGIC645MD230VCBINT
ENGLISH
The product adopts good sensitivity detector and integrated circuit. It gathers automatism,
convenience, safety, saving-energy and practicality functions. The wide detection field con-
sists of up and down, left and right service field. It works by receiving human motion infrared
rays. When one enters the detection field, it can start the load at once and identify automati-
cally day and night. Its installation is very convenient and its using is very wide.
SPECIFICATION:
• Power Source: 220-240V~
• Detection Range: 180°
• Power Frequency: 50/60Hz
• Detection Distance: max. 9 m (<24ºC)
• Ambient Light: <3-2000LUX (adjustable)
• Working Temperature: -20~+40ºC
• Time Delay:
• Min.10sec±3sec
• Max.7min±2min
• Working Humidity: <93%RH
• Power Consumption: approx. 0.5W
• Rated Load:
• Max.500W (incandescent lamp)
• *200W (energy-saving and LED lamps)
*Minimum power requirement: 5W 2-wire
• Detection Moving Speed: 0.6 - 1.5 m/s
• Installation Height: 1 - 1.8 m
• Protection degree: IP 20
FUNCTION:
• Can identify day and night: The consumer can adjust working state in different ambient
light. It can work in the daytime and at night when LUX knob is adjusted on the "sun"
position (max). It can work in the ambient light less than 3LUX when it is adjusted on the
"moon" position (min). As for the adjustment pattern, please refer to the testing pattern.
• Time-Delay is added continually: When it receives the second induction signals within the
first induction period, it will compute time once more on the basic of the first time-delay rest.
• The switch: "ON", "OFF", "PIR".
INSTALLATION ADVICE:
As the detector responds to changes in temperature, avoid the following situations:
• Avoid pointing the detector towards objects with highly reflective surfaces, such as mirrors
etc.
• Avoid mounting the detector near heat sources, such as heating vents, air conditioning
units, light etc.
• Avoid pointing the detector towards objects that may move in the wind, such as curtains,
tall plants etc.
CONNECTION:
¡Warning! ¡Danger of death through electric shock!
• Must be installed by professional electrician.
• Disconnect power source.
• Cover or shied any adjacent live components.
• Ensure device cannot be switched on.
• Check power supply is disconnected.
• Unload the faceplate of sensor and adjust the time and LUX knob.(refer to figure 1)
• Loose the screws in the connection terminal, and then connect the power to connection
terminal of sensor according to connection-wire diagram. (according to your actual
situation, here you can connect three wire or two wire)
• If you want to install it in circular hole, put the sensor into the hole and tighten the splay
bolt on both sides. If you want to install in quadrate hole, put the sensor into the hole, fix
the screw through the mounting hole.
• Install back the faceplate, switch on the power and then test it.
TEST:
• Set the function switch to "ON", set "TIME" anti-clockwise to minimum, "LUX" clockwise
to maximum.
• Switch on the power, the lamp should be on.
• Set the function switch to "OFF", the lamp should be off immediately.
• Set the function switch to "PIR", the sensor and its connected lamp will have no signal
at the beginning. After Warm-up 30sec, the sensor can start work. If the sensor receives
the induction signal, the lamp will turn on. While there is no another induction signal any
more, the load should stop working within 10sec±3sec and the lamp would turn off.
• Turn LUX knob anti-clockwise on the minimum (moon). If the ambient light is more than
3LUX, the sensor would not work and the lamp stop working too. If the ambient light is
less than 3LUX (darkness), the sensor would work. Under no induction signal condition,
the load should stop working within 10sec±3sec.
Note: when testing in daylight, please turn LUX knob to
the sensor lamp could not work!
If the lamp is more than 60W, the distance between lamp and sensor should be 60cm at least.
SOME PROBLEM AND SOLVED WAY:
• The load do not work:
a. Please check if the connection-wiring of power and load is correct.
b. Please check if the load is good.
c. Please check if the working light sets correspond to ambient light.
• The sensitivity is poor:
a. Please check if there has any hindrance in front of the detection window to affect to re-
ceive the signal.
b. Please check if the ambient temperature is too high.
c. Please check if the induction signal source is in the detection fields.
d. Please check if the installation height corresponds to the height showed in the instruction.
e. Please check if the moving orientation is correct.
• The sensor can not shut off the load automatically:
a. Please check if there is continual signal in the detection field.
b. Please check if the time delay is the longest.
c. Please check if the power corresponds to the instruction.
EN
SENSITIVITY
CONDITIONS TO AVOID
MOUNTING
CONNECTION-WIRE
2 wires
MANUFACTURER: MGL International
APAC: MGL GLOBAL SOLUTIONS LTD
info.apac@mgl-intl.com
Flat 4-1, 4/F, No. 35, Section 3 Minquan
East Road. Taipei, Taiwan.
Tel: +886 2-2508-0877
EMEA: MGL EUMAN S.L.
info.emea@mgl-intl.com
Parque Empresarial Argame, 33163
Morcín. Asturias, Spain.
Tel: +34 985-08-18-70
(SUN) position, otherwise
Good sensitivity
Fig. 1
3 wires
FULL MANUAL DOWNLOAD
You can download the complete manual at the URL
https://clogic-intl.com/clogic-645-md
Poor sensitivity
2 wires
3 wires
TEST
AMERICAS: MGL AMERICA, LLC.
info.na@mgl-intl.com
US East Coast: 2810 Coliseum Centre
Drive, Ste. 100. Charlotte, North Carolina,
28217 USA
Tel: +1 833 533-5899
US West Coast: 760 Challenger Street.
Brea, California 92821 USA
Tel: +1 310-728-6220
www.mgl-intl.com