Marineland SeaClone Protein Skimmer Guia De Inicio Rapido

Start Here - SeaClone Protein Skimmer (Hang-On or In-Sump)
1
Parts Check
Collection Cup Cover
Air Valve
Air Line
Collection Cup O-Ring
Connector
Triple Suction
"J" Skimmer
Mount
"J" Tube
O-Ring
Air Line
Maxi-Jet
Pump
Suction
Turbo-Venturi
Cups
Intake Connector
(TVIC)
Foam Cartridge
3
Hang-On Installation
B
Triple Suction Mount
IMPORTANT: SeaClone requires 4 inches
of clearance between tank edge and wall.
Questions or Missing Parts? Call Customer Service at: (800) 322-1266
M-F 7:30 am - 5:30 pm (Eastern Time) www.marineland.com
Quick Setup Guide
Collection Cup
Return
Spout
Tube
SeaClone
Coupling
Lock
Collar Tube
Riser Tube
Coupling Lock
"J" Tube O-Ring
4 In-Sump
A
Installation
Hang Pump/Turbo-
Venturi Assembly
in desired location.
NOTE: Use Triple
Suction Cup Mount
to attach pump to
inner aquarium wall.
2
Pump
Assembly
Air Valve
A.
Attach Air Valve and Air
Line Connector to Air Line.
Air Line
B. Thread Air Line through
Connector
Foam Cartridge.
C. Insert Air Line end into Turbo-
Air Line
Venturi Intake Connector (TVIC).
D. Attach TVIC to Maxi-Jet
"J" Tube O-Ring
Pump Intake. Slide Foam
Cartridge over TVIC.
Foam Cartridge
TVIC
4
B
Installation
IMPORTANT: SeaClone 100 requires at least
A. Insert Maxi-Jet
20 inches of clearance between bottom of
Pump Outlet into
sump and aquarium base. SeaClone 150
Skimmer Intake Port.
requires at least 27 inches of clearance.
NOTE: "J" Skimmer
Tube and Triple
Suction Mount are
not used for in-sump
Place assembled
installation.
SeaClone unit
in sump.
B. Secure Air Line
to clip on side of
SeaClone unit. If splash from water
overflow is a problem,
NOTE: Air Valve
position Return Spout near
must be out of water
the highest sump wall so that
at all times.
cascading water contacts and
flows down the wall into the sump.
3
Hang-On Installation
A
Triple Suction
Mount
A. Attach Suction
Cups to Triple
Suction Mount
B. Slide Triple
Suction Mount
onto Maxi-Jet Pump
C. Insert elbow end of "J" Skimmer Tube
into Skimmer Intake Port. Turn coupling
lock to secure.
D.
Fit "overhang" end of "J" Skimmer
Tube over Maxi-Jet Pump Outlet.
Turn coupling lock to secure.
E. Secure Air Line to clip on side
of SeaClone unit. NOTE: Air Valve
must be out of water at all times.
In-Sump
5
HANG-ON ADJUSTMENT
A. If air pocket forms inside "J" Skimmer Tube,
gradually close air valve while observing air
pocket. Stop when air pocket is purged from
tube. B.
setting.
adjustments -- 1/2 turn at a time, waiting an
hour between turns -- until foam collection
occurs.
IN-SUMP ADJUSTMENT
A. Gradually close the Air Valve until Skimmer
vortex tightens to a straight spiral.
SeaClone run for 24-hrs.
collected, begin small adjustments -- 1/2 turn
at a time, waiting an hour between turns -- until
foam collection occurs at a steady rate.
10/10 AQ12352
Maxi-Jet
Pump
Flow
Adjustment
PLUG IN YOUR
SYSTEM. Open
the Air Valve all
the way.
Let SeaClone run for 24 hrs at this
C. If no foam is collected, begin small
B. Let
C. If no foam is