Safety Rules - Super Ego 186000000 Manual De Instrucciones

For your own safety, read instruction manual before
starting operations.
Record the model No. And Serial No. And date of
purchase in your manual for future reference.

Safety rules

As with all machinery there are certain hazards
involved with operation and use of the machine.
Using the machine with respect and caution will
considerably lessen the possibility of personal
injury. However, if normal, safety precautions
are overlooked or ignored, personal injury to the
operator may result.
This machine was designed for certain applications
only. It is strongly recommended that this machine
NOT be modified and/or used for any application
other than for which it was designed.
WARNING: Failure to follow these rules may result
in serious personal injury.
1. FOR YOUR OWN SAFETY, READ INSTRUCTION
MANUAL BEFORE OPERATING THE TOOL. Learn
the tool's application and limitations as well as
the specific hazards peculiar to it.
2. KEEP GUARDS IN PLACE and in working order.
3. ALWAYS WEAR EYE PROTECTION.
4. GROUND ALL TOOLS. If tool is equipped with
three-prong plug, it should be plugged into a
three-hole electrical receptacle. If an adapter is
used to accommodate a two-prong receptacle,
the adapter lug must be attached to a known
ground. Never remove the third prong.
5. REMOVE ADJUSTING KEYS AND WRENCHES.
From habit of checking to see that keys and
adjusting wrenches are removed from tool
before turning it "ON".
6. KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
7. DON'T USE IN DANGEROUS ENVIRONMENT.
Don't use power tools in damp or wet locations,
or expose them to rain. Keep work area well
lighted.
8. KEEP CHILDREN AND VISITORS AWAY. All
children and visitors should be kept a safe
distance from work area.
9. MAKE WORKSHOP
padlocks, master switches, or by removing
starter keys.
10. DON'T FORCE TOOL. It will do the job better and
be safer at the rate for which it was designed.
CHILDRPROOF. With
ENGLISH
11. USE RIGHT TOOL. Don't force tool or attachment
to do a job for which it was not designed.
12. WEAR PROPER APPAREL. No loose clothing,
gloves, neckties, rings, bracelets, or other
jewerly to get caught in moving parts. Nonslip
foot wear is recommended. Wear protective
hair covering to contain long hair.
13. ALWAYS USE SAFETY GLASSES. Wear safety
glasses. Everyday eye-glasses only have impact
resistant lenses; they are not safety glasses.
Also use face or dust mask if cutting operation
is dusty.
14. SECURE WORK. Use clamps or a vise to hold
work when practical. It's safer than using your
hand and frees both hands to operate tool.
15. DON'T OVERREACH. Keep proper footing and
balance at all times.
16. 16. MAINTAIN TOOLS IN TOP CONDITION.
Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating
anda changing accessories.
17. DISCONNECT TOOLS before servicing and
when changing accessories such as blades, bits,
cutters, etc.
18. USE RECOMMENDED ACCESSORIES. The use of
improper accessories may cause hazards.
19. REDUCE THE RISK OF UNINETIONAL STARTING.
Make sure switch is in "OFF" position before
plugging in power cord.
20. NEVER STAND ON TOOL. Serious injury could
occur if the tool is tipped or if the cutting tool
is accidentally contacted.
21. CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part is damaged
should be carefully checked to ensure that it
will operate properly and perform its intended
function-check for alignment of moving parts,
mounting, and any other part that is damaged
should be properly repaired or replaced.
22. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Don't leave tool until comes
to a complete stop.
23. DRUGS, ALCOHOL, MEDICATION. Do not
operate tool while under the influence of drug,
alcohol or any medication.
24. MAKE SURE TOOL IS DISCONNECTED FROM
POWER SUPPLY while motor is being mounted,
connected or reconnected.
17