Publicidad
ENGLISH
FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment.
Industry Canada Regulatory Information
CAN ICES-3 (B)/NMB-3 (B)
Avis d'Industrie Canada
CAN ICES-3 (B)/NMB-3 (B)
Step 1: Install your batteries
Your universal remote requires two AAA alkaline batteries (not included).
To install the batteries:
1. Press and push the battery compartment cover to remove it.
2. Insert the batteries, matching the batteries to the (+) and (–) marks inside the battery compartment.
3. Push the battery cover back into place.
Battery Precautions:
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
• Always remove old, weak or worn-out batteries promptly and recycle or dispose of them in accordance with Local and National
Regulations.
Step 2: Program your Remote
Direct Code Entry
To program your remote to control up to two components, follow these steps:
1. Manually turn on the component you wish to program the remote to operate.
2. Find the five-digit code for your brand of TV or streaming player in the enclosed code
lists.
3. Press and hold the SET UP key until the indicator light turns on.
4. Release the SET UP key.
ENGLISH
2
5. Press and release the TV or STREAMING key. The indicator light blinks and then
remains lit.
6. Enter the five-digit code, using the REVERSE (for digit 1), PLAY/PAUSE (for digit 2),
FORWARD (for digit 3), PREVIOUS (for digit 4), STOP (for digit 5) and NEXT (for
digit 6) key. When each digit is entered, the indicator light blinks.
Note: If the indicator light blinks multiple times, you've entered an invalid code. Start from step 2
again.
7. Aim the remote at the component and press the POWER key. The component should
turn off.
Note: If your component does not respond, try all the codes for your brands. If the codes do not work
or your brand is not listed, try the Code Search Method that follows.
Auto Code Search
If your TV or streaming player does not respond after you have tried all the five-digit codes for your brand, or if your
brand is not listed, try searching for your code via the Auto Code Search Entry Method. To program your remote via
the Auto Code Search Entry Method, follow these steps:
1. Manually turn on the component you wish to program the remote to operate.
2. Press and hold the SET UP key until the indicator light turns on.
3. Release the SET UP key.
4. Press and release the component key you wish the remote to control—the TV or
STREAMING key. The indicator light blinks once and remains lit.
Important: Find the OK key on your remote (don't press it yet).
5. Press the POWER key to start the auto code search.
The remote will automatically go through all the codes in its library one by one. A
new code is sent every 4 seconds and the POWER key will blink when the new
code is sent. This may take several minutes to complete, but make sure you keep
watching your component until it turns off.
6. As soon as the component turns off, press the OK key within 4 seconds. The
indicator light turns off.
Note: If you wait longer than 4 seconds to press OK, the remote goes to the next code—you
will need to start the code search from step 1 again.
Manual Code Search
If your TV or streaming player does not respond after you have tried all the five-digit
codes for your brand, or if your brand is not listed, try searching for your code via the
Manual Search Entry Method. To program your remote via the Code Search Entry
Method, follow these steps:
1. Manually turn on the component you wish to program the remote to operate.
2. Press and hold the SET UP key until the indicator light turns on.
3. Release the SET UP key.
ENGLISH
Digit 1
Digit 2
Digit 4
Digit 5
3
4.
Digit 3
5.
Digit 6
6.
T
In
or
Illu
yo
SE
De
Th
OP
str
M
yo
M
Ar
sy
RE
pla
Re
IM
wh
the
dif
pla
EN
Publicidad
