Collapsible Bed Rail 1,50 M, For Compact Beds - JANE 50278 T01 Instrucciones De Uso

EN

Collapsible bed rail 1,50 m, for COMPACT beds

IMPORTANT: KEEP FOR FUTURE REFERENCE.
Read the entire instruction before assembling and installing this product.
If you sell or give away this product, make sure you give this instruction to the new owner.
Make sure that no parts are missing before fitting the rail (see parts list).
This bed rail complies with BS 7972:2001+A1:2009 - Designed in Spain - Made in China.
WARNING
1-The bedguard should not be used for children under the age of 18 months or when the child is over the age of 5 years. This
bed rail is used only when the child is able to climb in and out of bed unaided.
2-The bedguard should not be used as a substitute for a a cot, as it cannot provide the same level of safety as a cot.
3-Suitable for use with beds of the following sizes: minimum 80x190 cm and maximum: 150x200 cm. and mattress with a
thickness of between 15 to 30 cm.
4- Once installed, make sure the bed rail is correctly fitted and is secure.
5-The bedguard should not be used on a sleeping surface that is more than 600 mm from the floor. Never use on a bunk bed,
a child's bed or any other bed hat does not correspond to the present instructions.
6-To avoid risk of injury, carefully respect the present instructions when assembling, installing and using this bed rail.
7-Do not leave the child unattended while fitting or dismantling this product; the child should always be under an adult's supervision.
8-It should be checked periodically that the bed rail is always properly fitted and secure in place, and the locking mechanism on
the bedrail are securely fixed. The bedguard should be periodically checked for its general condition with particular reference
to the security of any locking mechanism and/or hinges that are used on the product.
9-Keep away from fire.
10-Do not use accessories that have not been approved by JANÉ. Additional and replacement parts should be obtained only from
the manufacturer.
11-The bedguard should not be used unless the fixings are in place and securely attached to both the bed and/or the mattress
and the bedguard.
12-This bed rail is suitable for all types of bed bases.
COMPONENTS
A. L-shaped folding bars (main structure)
B. Upper arch bars
C. Bed rail bars that are attached to each side of the folding system
D. Barrier fabric
E. Rear bars that form the stabilizing foot
ASSEMBLY
Follow the steps below using the drawings as a guide on page 2 of these instructions:
STEP 1.- First of all place the screws and threads that you will find in the bag with these instructions. Place them in the hole at the
vertex of each of the A-bars of the components. Now we will have two bars in the shape of "L" that have the button of the folding
system. Once the screws are in place, set them aside for later. We will join them to other bars in step 4.
STEP 2.- Join the two bars B in the shape of an arch.
STEP 3.- Insert the fabric D at one end of the B bars (already joined) in the form of an arch and pass it along its entire length
until you get to the other end.
STEP 4.- Join the bars A (previously separated) to each side of the bar B in which we have introduced the fabric.
After joining them, stretch the fabric downwards so that it is well adapted to its entire contour.
STEP 5.- Join the bars C to each other, leaving the plastic part of the adjustment at one end.
STEP 6.- Pass this bar through the lower fabric to adapt horizontally to each side of the folding point. First the metal side (6.1)
and then join the other end by pushing the plastic piece until you hear the fitting click (6.2).
STEP 7.- Stick each velcro of the fabric to the "L" bar with the folding system for a better fit.
Note: These velcro must always remain on the outside of the barrier and never on the inside to prevent the child from taking
them off.
Make sure that the fabric is well positioned, taking this into account.
STEP 8.- Finally, join the 2 E bars together and adapt each of the ends to the stabilizing foot.
5