General Safety - Campbell Hausfeld WF2010 Manual De Instrucciones Y Lista De Repuestos

Wire Feed Arc Welder

General Safety

WARNING
!
Always keep a fire
extinguisher accessible
while performing arc
welding operations.
Before starting or servicing any
electric arc welder, read and
understand all instructions. Failure
to follow safety precautions or
instructions can cause equipment
damage and/or serious personal
injury or death.
All installation, maintenance, repair
and operation of this equipment
should be performed by qualified
persons only in accordance with
national, state, and local codes.
WARNING
!
Improper use of electric
arc welders can cause
electric shock, injury,
and death! Take all
precautions described in this manual to
reduce the possibility of electric shock.
Verify that all components of the
arc welder are clean and in good
condition prior to operating the
welder. Be sure that the insulation
on all cables, wire feed gun, and
power cords is not damaged.
Always repair or replace damaged
components before operating the
welder. Always keep welder panels,
shields, etc. in place when operating
the welder.
Always wear dry, protective clothing
and welding gloves, and insulated
footwear.
Always operate the welder in a
clean, dry, well ventilated area. Do
not operate the welder in humid,
wet, rainy, or poorly ventilated
areas.
Be sure that the work piece is
properly supported and grounded
prior to beginning any electric arc
welding operation.
Coiled welding cable should be
spread out before use to avoid
overheating and damage to
insulation.
www.chpower.com
DANGER
!
(Con't)
gun in water. If the welder becomes
wet for any reason, be absolutely
certain that it is completely clean and
dry prior to attempting use!
Always shut the equipment off and
unplug the power prior to moving
the unit.
Always attach the work lead first.
Verify that the work piece is
securely grounded.
Always shut off electric arc welding
equipment when not in use and cut
off any excess wire from the wire
feed gun.
Never allow any part of the body to
touch the flux core wire and ground
or grounded work piece at the same
time.
When crouching, kneeling or at
elevations, be sure to insulate all
conductive parts, wear appropriate
protective clothing, and take
precautions to prevent injury from falls.
Never attempt to use this
equipment at current settings or
duty cycles higher than those
specified on the equipment labels.
Never use an electric arc welder to
thaw frozen pipes.
WARNING
!
Flying sparks and hot
metal can cause injury.
As welds cool, slag can
be thrown off. Take all
precautions described in this manual to
reduce the possibility of injury from
flying sparks and hot metal.
Wear ANSI approved face shield or
safety glasses with side shield
protection when chipping or
grinding metal parts.
Wear ear plugs when welding
overhead to prevent spatter or slag
from falling into ears.
WARNING
!
Electric arc welding
operations produce
intense light and heat
and ultraviolet (UV)
rays. This intense light
and UV rays can cause injury to eyes
Never immerse the and skin. Take all precautions described
wire or wire feed in this manual to reduce the possibility
of injury to eyes and skin.
without eye protection as described
above. Never use a shade filter lens
that is cracked, broken, or rated below
number 10. Warn others in the area not
to look at the arc.
Electric arc welding
operations cause sparks
and heat metal to
temperatures that can
cause severe burns! Use protective
gloves and clothing when performing
any metal working operation. Take all
precautions described in this manual to
reduce the possibility of skin and
clothing burns.
Heat and sparks
produced during electric
arc welding and other
metal working
operations can ignite flammable and
explosive materials! Take all precautions
described in this manual to reduce the
possibility of flames and explosions.
2
All persons operating this
equipment or in the area while
equipment is in use must wear
protective welding gear including:
welding helmet or shield with at
least shade 10 filter, flame resistant
clothing, leather welding gloves,
and full foot protection.
Never look at arc
WARNING
!
welding operations
WARNING
!
Make sure that all persons in the
welding area are protected from
heat, sparks, and ultraviolet rays.
Never touch work pieces until
completely cooled.
WARNING
!
Remove all flammable materials
within 35 feet (10.7 meters) of
welding arc. If removal is not
possible, tightly cover flammable
materials with fire proof covers.
Do not operate any electric arc
welder in areas where flammable or
explosive vapors may be present.
Take precautions to be sure that
flying sparks and heat do not cause
flames in hidden areas, cracks,
behind bulkheads, etc.