Environmental Protection - Crown CT22023 Manual Original

página de 141

/ 141
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

Rotation to the right (drilling, screwing in) - move the

reverse switch 10 to the left�

Rotation to the left (unscrewing) - move the reverse

switch 10 to the right�

Spindle automatic locking

If the on / off switch 11 is not pressed, the spindle of the

power tool is locked this enables to use the power tool

as an ordinary screwdriver (for example it can be used

to tighten manually screws or bolts, if the battery is low)�

Turn handle (see fig. 6)

Turn handle 12 can be put into 2 positions relating to

the horizontal axis of body 5 (see fig. 6). This allows

on / off switch 10 to be put into the position most

convenient for working and allows to work in hard to

reach places�

• Press onto lock 8 and while holding it in position,

rotate handle 12 as shown onto fig. 6.

• Release lock 8�

• To rotate the turn handle 12 to its original position, re-

peat the above operations in reverse order� Attention: it

is possible to turn the handle 12 in only one direction.

Recommendations on the power tool

operation

• Install accessories as described above�

• Always turn off the power tool before installing it on

the fastener� Rotating accessories can slip or damage

the slot of the fastener�

• Special accessories (drill bits with hex shank 1/4")

must be used for drilling and not exceed the recom-

mended drilling diameter�

• Grease the drill bit regularly when drilling holes in met-

als (except drilling non-ferrous metals and their alloys)�

• To make fastening of screws easier and in order to

prevent cracking of the work pieces, first drill a hole

with a diameter equal to 2/3 of a diameter of the screw�

Power tool maintenance / preventive

measures

Before execution of any procedures, centre the re-

verse switch 10.

Battery maintenance instruction

• Charge timely before the battery is completely ex-

hausted� Stop operation in low power and charge it

immediately�

• Do not overcharge when the battery is full, otherwise

it will shorten the life time�

• Charge battery in the room temperature of 10°C

to 40°C (50°F to 104°F)�

• Charge battery every 6 months without operation for

a long time�

The manufacturer reserves the possibility to introduce changes.

• Replace worn out batteries in time� Decline of pro-

duction or a significantly shorter runtime of the power

tool after charging indicates aging of the battery and

the need for replacement� It should be taken into ac-

count that the battery may discharge faster if the works

take place in the temperature below 0°С.

• In case of long time storage without use, it is recom-

mended to store the battery at room temperature, it

should be charged to 50%�

Cleaning of the power tool

An indispensable condition for a safe long-term exploi-

tation of the power tool is to keep it clean� Regularly

flush the power tool with compressed air thought the

ventilation slots 9�

After-sales service and application service

Our after-sales service responds to your questions

concerning maintenance and repair of your product as

well as spare parts� Information about service centers,

parts diagrams and information about spare parts can

also be found under: www.crown-tools.com.

Transportation of the power tools

• Categorically not to drop any mechanical impact on

the packaging during transport�

• When unloading / loading is not allowed to use any

kind of technology that works on the principle of clamp-

ing packaging�

Li-Ion batteries

The contained Li-Ion batteries are subject to the Dan-

gerous Goods Legislation requirements� The user can

transport the batteries by road without further require-

ments�

When being transported by third parties (e�g�: air trans-

port or forwarding agency), special requirements on

packaging and labelling must be observed� For prepa-

ration of the item being shipped, consulting an expert

for hazardous material is required�

Dispatch batteries only when the housing is undam-

aged� Tape or mask off open contacts and pack up the

battery in such a manner that it cannot move around

in the packaging� Please also observe possibly more

detailed national regulations�