Switching The Appliance On / Off - Crown CT36046 Manual Original

Ocultar thumbs

Contenido

página de 81

/ 81
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

21 Safety valve

22 Drain valve

23 Oil bottle *

24 Fitting *

25 Nut for installing rubber mount *

26 Bolt for installing rubber mount *

27 Washer for installing rubber mount *

28 Wheel installing stud *

29 Wheel installing washer *

30 Wheel installing nut *

31 Hose *

32 Hose clamp *

33 Quick-change fitting *

34 Plug *

35 Air filter housing

36 Filter element *

37 Air filter cover

* Optional extra

Not all of the accessories illustrated or described

are included as standard delivery.

Installation and regulation of appliance

elements

Before any procedures, be sure to switch off the

appliance, remove the current-carrying cable from

the socket and discharge pressure in receiver 17

(pulling by the ring of safety valve 21).

Do not draw up the fastening elements

too tight to avoid damaging the thread.

Mounting / dismounting / setting-up of

some elements is the same for all appli-

ance models, in this case specific mod-

els are not indicated in the illustration.

Rubber mounts assembly / disassembly (see fig. 1-2)

• Install the rubber mounts 5 as shown in fig. 1-2.

• Disassemble in the reverse sequence�

Wheels assembly / disassembly (see fig. 3)

[CT36028, CT36029, CT36047]

• Install wheels 2 as shown in fig. 3.

• Disassemble in the reverse sequence�

Connecting / disconnecting the air hose (see fig. 4-5)

[CT36046, CT36047]

• Attach hose clamp 32 to the end of hose 31 (see

fig. 4.1).

• Install fitting 24�

• Tighten the screw of hose clamp 32�

• When connecting, screw fitting 24 on outlet fitting 12

or 15 (see fig. 4.2).

• When disconnecting unscrew fitting 24�

[CT36028, CT36029]

• When connecting, insert (until it clicks) quick-change

fitting 33 into outlet fitting 12 or 15 (see fig. 5.1).

• When disconnecting, move the bush of the quick-

change connection, as shown in fig. 5.2, and remove

quick-change fitting 33�

Initial operating of the appliance

Oil filling (see fig. 6-7)

Attention: The manufacturer of the

appliance does not fill crankcase 19

with oil in order to comply with the

technical conditions for transportation.

Therefore, before using it is required to fill

the appliance with oil of the recommended

brand. Operation of the appliance without oil in

crankcase 19 or at the oil level less than minimum

will result in the appliance damage; in this case you

will lose the right to the warranty repair service.

• Place the appliance on a flat horizontal surface.

• Clean an area around the oil hole with a cloth and

remove the plug 34 (see fig. 6.1).

• Carefully pour oil into crankcase 19 (it is

recommended to use a funnel)� The oil level is the

upper limit of the red point on viewport 20 (see

fig. 6.2). Wait for 5 minutes and then check the oil

level again, top up to the maximum level mark, if

necessary� Attention: do not exceed the maximum

level mark.

• Install plug 8 as shown in figure 7.1. Attention:

plug 8 has a special valve that prevents from

pressure increase inside crankcase 19. It is

strictly forbidden to replace plug 8 with plug 34

or other objects.

• To ensure even distribution of oil in crankcase 19

at the first start-up and after a long idle time, it is

recommended to let the appliance run without a load

for 5 minutes� To do this, unscrew drain valve 22 (as

when draining condensate, see the description below),

also pull by the ring of safety valve 21 and hold it, then

switch on the appliance�

For refilling use the oil supplied with the

appliance� You can also use engine oil -

SAE30 (if the appliance is used at the

temperature above 10°C) or SAE10 (if the

appliance is used at temperatures below 10°C)� Do not

mix oils of different grades�

Before operating the appliance

• Make

sure

specifications printed on the appliance.

• Check power cable and extension cord condition; if

any damage is detected, the cable shall be replaced�

• Check the condition of the air hose; if damaged,

replace it�