Briteq Beam Wizard 5x5 Manual De Instrucciones página 8

ENGLISH
General instructions for setup.
The SETUP-menu has three logically structured levels, see the menu structure on the previous page.
 Press the [MENU] button to enter the SETUP-menu. (Press about 3s while Menu [LOCK] function is
active)
 Press the ▲/▼/◄/► buttons to browse the different functions of the setup menu until the required function
is shown on the display.
 Press the [ENTER] button to access the function and change its parameters.
 Use ▲/▼ buttons to change the value.
 Press the [ENTER] button again confirm.
 To jump to a higher menu level: press the [MENU] button.
 To exit the SETUP-menu: press the [MENU] button several times until the standard display is shown.
Remark: to make things easier you will always enter the SETUP-menu at the last used location.
[SET CONFIG > ADDRESS Set] –
All functions in this level are related to addressing of the unit.
[DMX-Address]
Used to set the desired DMX-address.
 Press the ▲/▼/◄/► buttons until the desired function is showing on the display.
 Press the [ENTER] button: the values can be changed
 Use ▲/▼ buttons to select the desired DMX512 address. The last occupied DMX-address is also shown:
makes it easier to set the address of the next unit in the chain.
 Once the correct address shows on the display, press the [ENTER] button to confirm.
Note: on RDM-compatible controllers this option can also be remotely set.
[IP-Address]
Used to set the IP address of the projector while controlled using the Ethernet ports.
 Press the ▲/▼/◄/► buttons until the desired function is showing on the display.
 Press the [ENTER] button: the values can be changed
 Use ▲/▼/◄/► buttons to set the desired IP-address.
 Once the correct address shows on the display, press the [ENTER] button to confirm.
Remark: an IP address in ArtNet topology generally starts with 2.x.x.x or 10.x.x.x with 255.0.0.0 for netmask.
[IP-NetMask]
Used to set the Net Mask of the projector while controlled using the Ethernet ports.
Based on the IP-address the correct netmask is already set, you can still change it if really needed:
 Press the ▲/▼/◄/► buttons until the desired function is showing on the display.
 Press the [ENTER] button: the values can be changed
 Use ▲/▼ buttons to select the desired netmask, there are 3 options:
 255.000.000.000
 255.255.000.000
 255.255.255.000
 Once the correct option shows on the display, press the [ENTER] button to confirm.
[DMX Universe]
Used to set which DMX-universe should be used while controlled via the Ethernet ports.
 Press the ▲/▼/◄/► buttons until the desired function is showing on the display.
 Press the [ENTER] button: the values can be changed
 Use ▲/▼ buttons to set the desired DMX universe (000 - 255).
 Once the correct DMX universe shows on the display, press the [ENTER] button to confirm.
[IP Protocol]
Used to select which Ethernet protocol you want to use for communication.
 Press the ▲/▼/◄/► buttons until the desired function is showing on the display.
 Press the [ENTER] button: the values can be changed
 Use ▲/▼ buttons to set the desired Protocol.
 Once the correct protocol shows on the display, press the [ENTER] button to confirm.
Remark: currently only Art-Net is available, with future firmware updates extra protocols will be added.
BRITEQ
®
6/107 BEAM WIZARD5x5-RGBW
OPERATION MANUAL