Cadet CM162 Guía Para El Propietario página 4

INSTALLATION INSTRUCTIONS
__________________________
After you have followed all instructions in PART ONE you are ready to install the heater assembly.
How do I configure my wattage?
Multi-Watt Element Wiring Configuration:
STEP 1 STEP 1 STEP 1
The multi-watt heaters listed below are factory set for the highest possible wattage. If you would like to keep the wattage at the highest
setting, proceed to Step 2. If you would like to reduce your heater's wattage from the factory setting, refer to the table below that corre-
sponds to your heater model. Once you are finished, proceed to Step 2.
DO NOT DISCONNECT THE BLUE CONNECTOR FROM TERMINAL "D"
CM202/CM208
2000 No change
Disconnect and cut wire with Blue Connector at
Terminal B. Cap loose end with wire connector
1500
or wrap with electrical tape. Move Yellow
Connector from Terminal A to Terminal B.
Disconnect and cut wire with Blue Connector at
Terminal B. Cap loose end with wire connector
1200
or wrap with electrical tape. Move Yellow
Connector from Terminal C to Terminal B.
Cut jumper wire between terminals A and C.
Remove connectors at Terminals B and C.
Move Yellow Connector from Terminal A to
800
Terminal C. Cap loose ends with wire
connector or wrap with electrical tape.
Cut jumper wire between terminals A and C.
Remove connectors at Terminals B and C.
500
Cap loose ends with wire connector or wrap
with electrical tape.
How do I insert the heater assembly into the wall can?
STEP 2 Install Heater Assembly
Turn heater assembly upside down (Element down with motor
facing you). Connect the supply wires to the heater wires with
connectors (See Figure 7). Now rotate the heater so the element
and the fan are facing you.
For VERTICALLY MOUNTED units the element should be at the
top. Insert the bottom edge of the heater assembly into the half
round slots (tabs) in the bottom lip of the wall can (See Figure 8a).
[IMPORTANT: Push wires into bottom of wall can during insertion. Be sure that supply wires are not caught between motor and wall
can.] Attach assembly at top with screw provided.
For HORIZONTALLY MOUNTED units the element should be to the left. Insert the right edge of the heater assembly into the half round
slots (tabs) on the right side of the wall can (See Figure 8b). [IMPORTANT: Push wires into right side of wall can during insertion. Be
sure that supply wires are not caught between motor and wall can.] Attach assembly at left with screw provided.
STEP 3
Install Grill
Secure grill with the screws provided. If you have a built-in thermostat model, slide thermo stat knob onto
shaft. Turn power on at the electrical panel board.
Warranty is void if any material is sprayed on the element or blower. Use a paint mask to cover any exposed
areas of the heater if walls are to be textured or painted.
GRILL
Page 4
Figure 4a
Vertical
Mounting
WIRE CONFIGURATION
B
FACTORY SET
AT 1600 WATTS
DO NOT DISCONNECT THE BLUE CONNECTOR FROM TERMINAL "A"
Figure 8a
TAB
Figure 8b
Figure 4b
Horizontal
Mounting
__________________________
Part Two
DO NOT DISCONNECT THE BLUE CONNECTOR FROM TERMINAL "A"
C
CM162/CM168
A
MODELS
Figure 5a
CM202
CM208
2000
Watt
Config-
uration
Shown
(table
above
GRILL
(continued)
WIRE CONFIGURATION
1600 No change
Disconnect and cut wire with Blue
Connector at Terminal C. Cap loose
end with wire connector or wrap
900
with electrical tape. Move Yellow
Connector from Terminal B to
Terminal C.
Disconnect and cut wire with Blue
Connector at Terminal C. Cap loose
700
end with wire connector or wrap
with electrical tape.
For
CM202/CM208
B
A
and
C
D
left)
FACTORY SET Figure 6a
AT 2000 WATTS
DO NOT DISCONNECT THE BLUE CONNECTOR FROM TERMINAL "D"
TAB
Figure 7
Figure 5b
For
C
WIRE CONFIGURATION
MODELS
No change
2000
CM162
Disconnect and cut wire with Blue Connec
and
Terminal B. Cap loose end with wire conn
1500
CM168
or wrap with electrical tape. Move Yellow
Connector from Terminal A to Terminal B
1600
Disconnect and cut wire with Blue Connec
Watt
Terminal B. Cap loose end with wire conn
B
1200
Config- or wrap with electrical tape. Move Yellow
Connector from Terminal C to Terminal B
uration
Cut jumper wire between terminals A an
Shown
Remove connectors at Terminals B and
800 Move Yellow Connector from Terminal A
(table
Terminal C. Cap loose ends with wire
A
above)
connector or wrap with electrical tape.
Cut jumper wire between terminals A an
Remove connectors at Terminals B and
Figure 6b
500
FACTORY SET
Cap loose ends with wire connector or w
AT 1600 WATTS with electrical tape.
DO NOT DISCONNECT THE BLUE
Supply Wires
Heater
Wires
Motor
Top
CM162
16
9
7