Cadet The Com-Pak Max CM162 Guia Del Propietario

Ocultar thumbs Ver también para The Com-Pak Max CM162:

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

The Com-Pak Max
The Com-Pak Max
Vertical
Horizontal
WARNING
Turn the electrical power off at the electrical panel
board (circuit breaker or fuse box) and lock or tag the
panel board door to prevent someone from turning on
power while you are working on the heater. Failure
to do so could result in serious electrical shock,
burns, or possible death.
1. Read all instructions before using this heater.
2. Read all information labels. Verify that the electrical
supply wires are the same voltage as the heater.
3. All electrical work and materials must comply with the
National Electric Code (NEC), the Occupational Safety
and Health Act (OSHA), and all state and local codes.
4. Connect the grounding pigtail (copper wire) provided
in the wall can to the supply ground wire.
5. If you need to install a new circuit or need additional
wiring information, consult a qualified electrician.
6. Protect electrical supply from kinks, sharp objects, oil,
grease, hot surfaces or chemicals.
7.
WARNING
Overheating or fire may occur. DO NOT install the
heater in a floor, ceiling, behind doors, or outdoors.
360-693-2505 Fax: 360-694-8668 P.O. Box 1675 Vancouver, WA 98668-1675
OWNER'S GUIDE
IMPORTANT INSTRUCTIONS
8.
9.
10.
11.
12. Use this heater only as described in this manual. Any other
SAVE THESE INSTRUCTIONS
Features & Benefits
Thermal Safeguard
I
High temperature manual reset: turns off
heater if normal operating temperatures
are exceeded
Finned tubular air heating element
I
Powder coat paint process eliminates
I
sharp cutting edges
Three year extended warranty on
I
element and motor
Factory tested
I
Models:
The Com-Pak Max
CM162
CM202
CM162T
CM202T
TOOLS REQUIRED:
Phillips Screwdriver
Straight Screwdriver
Wire Strippers
WARNING
Fire or explosion may occur. Heater has hot and arcing or
sparking parts inside. Do not install heater in any area where
combustible vapors, gases, liquids, or excessive lint or dust
are present.
WARNING
Burn Hazard. This heater is hot when in use. To avoid burns,
do not let bare skin touch hot surfaces. Use extreme caution
when any heater is used by or near children or invalids and
whenever the heater is left operating unattended.
WARNING
Risk of Electrical Shock. Keep all foreign objects out of heater.
Do not operate after heater malfunctions or has been dropped
or damaged in any manner.
WARNING
Risk of Fire. Do not block heater. Heater must be kept clear
of all obstructions: a minimum of 3 feet in front, 6 inches above
and on both sides. Heaters must be kept clean of excessive
lint, dirt and debris. (See Maintenance Instructions).
use not recommended by the manufacturer may cause fire,
electrical shock, or injury to persons.
CM208
CM208T
Utility Knife
(4) 1
/
" Wood Screws
1
2
3 Insulated Wire Connectors
1 Strain Relief Connector

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Cadet The Com-Pak Max CM162

  • Página 1 The Com-Pak Max OWNER’S GUIDE Features & Benefits The Com-Pak Max Thermal Safeguard High temperature manual reset: turns off • heater if normal operating temperatures are exceeded Finned tubular air heating element Powder coat paint process eliminates sharp cutting edges Three year extended warranty on element and motor Vertical...
  • Página 2: Instructions And Safety Information

    Note wall can position for correct horizontal mounting. NOT APPROVED FOR CEILING MOUNT. THERMOSTAT: A thermostat is required for models without a built-in thermostat. Vertically mounted units can use in-built thermostat. Horizontally mounted units must use a wall thermostat. A Cadet Electronic Thermostat is recommended for ultimate control and comfort.
  • Página 3 Installation Instructions Part Two WARNING Turn the electrical How do I configure my wattage? power off at the STEP 1 Multi-Watt Element Wiring Configuration: The multi-watt heaters listed below are factory set for the highest possible wattage. If you would like to keep the wattage electrical panel at the highest setting, proceed to Step 2.
  • Página 4 Installation Instructions How do I insert the heater assembly into the wall can? STEP 2 Install Heater Assembly Turn heater assembly upside down (Element down with motor facing you). Connect the supply wires to the heater wires with connectors (See Figure 7). Now rotate the heater so the element and the fan are facing you.
  • Página 5: Troubleshooting Chart

    Warranty Maintenance: For more effective and safer operation and to 7. IN THE EVENT CADET ELECTS TO REPLACE ANY PART OF YOUR prolong the life of the heater, read the Owner’s Guide and follow CADET PRODUCT, THE REPLACEMENT PARTS ARE SUBJECT the maintenance instructions included with each heater.
  • Página 6: Guía Para El Propietario

    El Com-Pak Max GUÍA PARA EL PROPIETARIO Características y El Com-Pak Max Beneficios Protección térmica Reglaje manual de alta temperatura: apaga • el calentador si se sobrepasan las temperaturas de operación normales Elemento calentador de aire tubular con aletas Proceso de pintura en polvo por capas elimina los bordes cortantes agudos Garantía extendida de tres años para Vertical...
  • Página 7: Instrucciones Para La Instalación

    TERMOSTATO: Se requiere un termostato para los modelos que no lo traigan incorporado. Las unidades montadas verticalmente pueden usar un termostato incorporado. Las unidades de montaje horizontal deben usar un termostato mural. Se recomienda usar un termostato electrónico Cadet para una comodidad y un control óptimos. ¿Cómo se instala el calentador en una ¿Cómo se instala el calentador en una...
  • Página 8 Instrucciones para la Instalación Parte Dos ¡ADVERTENCIA! ¿Cómo configuro el vatiaje? Desconecte la PASO 1 Multi-Watt Element Wiring Configuration: energía eléctrica en Los calentadores de vatiaje múltiple indicados a continuación vienen fijados de fábrica en el vatiaje más alto posible. Si desea mantener el vatiaje en el ajuste más alto, prosiga con el paso 2.
  • Página 9: Funcionamiento Y Mantenimiento

    Instrucciones para la Instalación ¿Cómo se coloca la unidad del calentador en la cámara de pared? Instale el conjunto del calentador STEP 2 PASO 2 Voltee el conjunto del calentador (dejando en frente suyo el elemento situado bajo el motor). Empalme los cables de suministro con los del calentador mediante conectores (consulte la figura 7).
  • Página 10: Diagrama De Resolución De Problemas

    8. Estas garantías le otorgan derechos legales específicos y es posible que GARANTÍA LIMITADA DE TRES AÑOS: Cadet reparará o reemplazará todo usted tenga otros derechos que varíen de un estado a otro. Cadet no elemento o motor serie Com-Pak Max (CM) que se determine que está...

Tabla de contenido