Ec Declaration Of Conformity - RediPower RP9105QB Manual Del Usaurio

EN
English
INSTRUCTION MANUAL
Air Supply Requirements
1. Supply tool with 90 psig (6.3 bar) of clean, dry air. Higher
pressure drastically reduces tool life.
2. Connect tool to air line using pipe, hose and fitting sizes
shown in the diagram below.
3. Do not install a quick coupler directly into the grinder
throttle handle.
4. Minimum compressor requirement: 3hp (2238 w), 60 gal.
air tank.
1/4" NPT 3/8" (10mm)
Lubrication
Use an air line lubricator with SAE #10 oil, adjusted to two
drops per minute. If an air line lubricator cannot be used,
add air motor oil to the inlet once a day.
Maintenance
1. Disassemble and inspect air motor every three months
if the tool is used every day. Replace damaged or worn
parts.
2. High wear parts are underlined in the parts list.
Copyright 2008, Chicago Pneumatic Tool Co. LLC
All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. This applies in particular to trademarks, model
denominations, part numbers and drawings. Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not
covered by Warranty or Product Liability.
1/2" (12mm)
CA048362 (1/2") NPT
1/2" (12mm)
CA048360 (1/2") NPT
CA048361 (1/2") NPT
RP9105QB/RP9106QB/RP9108QB/RP9110QB

EC DECLARATION OF CONFORMITY

We, Chicago Pneumatic Tool Co. LLC,13325 Carowinds
Blvd., Charlotte, NC 28273 USA, declare under our sole
responsibility that the product to which this declaration relates,
is in conformity with the requirements of the Council Directive
of June 1998 on the approximation of the laws of the Member
States relating to machinery (98/37/EC).
Machine Name RP9105QB/RP9106QB/RP9108QB/
RP9110QB Mini Die Grinder
Machine Type Power tool equipped with 1/4 in. or 6 mm collet
chuck for use with various burrs for polishing and grinding -
No other use is permitted
Serial No. Tools with No. C00501-2008 or higher
Technical Data
1/4 in. or 6 mm collet
Free speed 28,000 RPM (RP9105QB); 23,000 RPM
(RP9106QB); 23,000 RPM (RP9108QB); 27,000 RPM
(RP9110QB)
Air pressure 90 psi (6.3 bar)
Harmonized Standards Applied EN792-9
National Standards Applied ISO 8662-13, EN ISO 15744
Name and Position of Issuer Bruno Blanchet, General
Manager
Signature of Issuer_______________
Date of Issue August 15, 2008
Noise & Vibration Declaration*
Sound pressure level 80 dB(A), re. EN ISO 15744. For sound
power, add 11 dB(A).
Vibration value 4.5 m/s 2 (RP9105QB); 2.7 m/s
2.6 m/s 2 (RP9108QB); 3.15 m/s
8662-13.
For making estimates of daily vibration exposures, useful
information may be found in CEN/TR 15350: 2006,
"Mechanical vibration - Guideline for the assessment of
exposure to hand-transmitted vibration using available
information including that provided by manufacturers of
machinery"
*These declared values were obtained by laboratory type testing in
compliance with the stated standards and are not adequate for use in
risk assessments. Values measured in individual work places may be
higher than the declared values. The actual exposure values and risk
of harm experienced by an individual user are unique and depend upon
the way the user works, the workpiece and the workstation design, as
well as upon the exposure time and the physical condition of the user.
We, Chicago Pneumatic, cannot be held liable for the consequences
of using the declared values, instead of values reflecting the actual
exposure, in an individual risk assessment in a work place situation over
which we have no control.
Mini Die Grinder
2 (RP9106QB);
2 (RP9110QB) re. ISO