Publicidad
Idiomas disponibles
Idiomas disponibles
Disassembly
Turn "OFF" hot and cold water supplies, then
rotate handle counterclockwise until the lever
points up to relieve pressure. Remove handle
parts.
1. For handle style A & B, remove handle insert or
plug button. Take out handle screw, remove
handle and washer.
For handle style C,
remove cap screw and handle, then remove
handle screw and adapter
2. Remove temperature limit stop, key stop and
stop tube. Lift out retainer clip. Rotate cartridge
shell between the eleven and one o'clock
positions, grasp the cartridge stem with pliers
and pull out cartridge.
Reassembly
Orient cartridge, see illustration on previous page,
then re-insert cartridge by pushing it into the body
until the cartridge ears are flush and aligned with
the top and bottom of the valve body. Replace the
retainer clip with the legs straddling the cartridge
ears. Slide down into the bottom slot.
prevents rotation and locks the cartridge into the
body. Reinstall stop tube and parts. Limit stop
must be installed with offset at TOP (12 o'clock)
position for maximum hot water. The notched flat
on the stem must point DOWN when mounting the
handle.
TEMPERATURE
KEY STOP
LIMIT STOP
To Adjust Temperature Limit
Stops
CAUTION: Due to season temperature change of
the cold water supply, the temperature limit must
be readjusted accordingly to maintain the desired
maximum discharge temperature.
1. Rotate the handle counterclockwise to stop and
let water run till cold water is purged, check
temperature.
2. Rotate handle to off, remove handle parts (see
Disassembly) and temperature limit stop, rotate
Helpline
Call our toll free helpline number:
1 (800) 289-6 6 3 6
1 (800) BUY-MOEN
For answers to any product, installation
replacement parts, or warranty questions.
Hours of operation are:
8:00 A.M. - 8 P.M. EST. Monday - Friday
8: A.M. - 6:30 P.M. EST. Saturday
clockwise to decrease and counterclockwise to
increase maximum hot water temperature,
reinstall temperature limit stop and handle (TIP:
Do not screw handle in until desired maximum
temperature is achieved)
3. Repeat
temperature is achieved.
TEMPERATURE
LIMIT STOP
ESCUTCHEON
SCREWS (2)
SPOUT
This
Trim
MAKE SURE ALL WATER SUPPLIES ARE OFF
TO INSTALL TRIM AFTER ROUGH-IN
1. Slide the flange into the long end of the shower
ROTATE LIMIT
arm, wrap both ends of the shower arm with
STOP CLOCKWISE
TO REDUCE
teflon tape and screw long end into pipe ell
FULL HOT POSITION
inside the wall. Do not install shower head at
this time.
2. Install tub spout (see spout installation
instructions).
3. Remove screw holding plaster ground and
stop tube guard in place and discard.
Temporarily install handle.
divert water to tub spout and flush the shower
riser for 15 seconds. Install shower head and
check for leaks. If there are no leaks, turn off
and remove handle and limit stop
4. Install escutcheon plate with 2 screws
provided. Mount with the escutcheon notch up.
5. Install
Temperature Limit Stop section) ensure that
notched flat on the cartridge stem points
DOWN.
7:30 A.M. - 5:00 P.M. EST. Monday - Friday
7:30 A.M. - 5:00 P.M. EST. Monday - Friday
Visit our website at www.moen.com for more information
steps
until
desired
maximum
PIPE ELL
SHOWERHEAD
SHOWER ARM
NOTCH
CC
CONNECTIONS
ESCUTCHEON
TUB LOOKOUT NIPPLE
Turn water on,
temperature
limit
stops
In Canada:
1-800-465-6130
Hours of operation are :
Toronto:
1-905-829-3400
Hours of operation are :
Handle Attachment :
For handle style A & B : Mount handle on stem
and replace handle screw tightly. Snap handle
insert or plug button in place.
For handle style C : Mount handle adapter on
stem and replace handle screw tightly.
handle on adapter and replace set screw.
Not for use with Moentrol valves
TO REMOVE STOP VALVE
Always turn water supply OFF before disassembly
(see Disassembly).
Removal of stop valve:
1. Remove handle parts (see Disassembly) and
escutcheon.
2. Using snap ring pliers, remove retaining ring
from valve body.
3. Grip stop valve stem with pliers and rotate
slightly to remove from valve body.
Re-Installation of new stop valve:
1. Check to be sure that stop valve stem is fully
seated in plug.
2. Insert stop valve until fully seated beyond
retaining ring groove in valve body.
3. Using snap ring pliers, place retaining ring in
valve body, making sure that ring is fully
seated.
4. Check orientation of stop valve for water flow.
(Stop is in the off position when screwdriver
slot is vertical).
5. Turn on water supply.
To Eliminate Cross-Piping On Back-
To-Back Installations, or To Correct
Reversed Rough-In Where Hot and
Cold Positions Are Reversed:
Remove cartridge assembly, rotate 180° and re-
install. (See Reassembly) Caution: Make sure
notch on stem is point up.
(see
In Mexico:
(84) 88-08-26, 88-08-27,
o 91-800-84345
Hours of operation are :
8:00 A.M. - 8 P.M. EST. Monday - Friday
8: A.M. - 6:30 P.M. EST. Saturday
Mount
.
2
Publicidad
